AS 1359.101-1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Rotating electrical machines - General requirements Rating and performance
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
22-05-2024
01-01-1997
Important note : All end users must be registered with an Account prior to user licenses being assigned.Specifies duty types, ratings, site operating conditions, electrical operating conditions, thermal performance, other performance aspects, rating plate markings and tolerances for all types of rotating electrical machines not covered by other Standards. This Standard is identical with and has been reproduced from IEC 34-1:1996 (edition 10).
| Committee |
EL-009
|
| DocumentType |
Standard
|
| ISBN |
0 7337 1214 2
|
| Pages |
70
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
This standard is applicable to all rotating electrical machines except those covered by other IEC standards û for example, IEC 349.Machines within the scope of this standard may also be subject to superseding, modifying or additional requirements in other publications û for example, IEC 79, and IEC 92.NOTE û If particular clauses of this standard are modified to meet special applications, for example machines subject to radioactivity or machines for aerospace, all other clauses apply in so far as they are compatible.
| Standards | Relationship |
| IEC 60034-1:1996 | Identical |
First published as in part as part of AS C34-1927.
AS C35 first published 1927.
AS C36 first published 1927.
AS C38 first published 1927.
AS C34-1927 redated 1932.
As C35-1927 redated 1932.
AS C36-1927 redated 1932.
AS C38-1927 redated 1932.
AS C34-1932, AS C35-1932, AS C36-1932 and AS C38-1932 revised, amalgamated and redesignated AS C319-1956 (being endorsement of BS 2613:1955 without Amendment).
Second edition 1958 (being endorsement of BS 2613:1957 without Amendment).
AS C319-1958 revised and redesignated in part as AS 1359.1-1974, AS 1359.4-1974, AS 1359.30-1974, AS 1359.31-1974, AS 1359.32-1974, AS 1359.40-1974, AS 1359.60-1974 and AS 1359.69-1974.
AS 1360.10 first published 1975.
Second edition AS 1359.60-1981.
Second edition AS 1359.4-1983.
Second edition AS 1359.31-1986.
Third edition AS 1359.60-1986.
Second edition AS 1359.1-1987.
As 1359.30-1974 and AS 1360.10-1975 revised, amalgamated and designated AS 1359.30-1987.
Second edition AS 1359.40-1977.
AS 1359.1-1987, AS 1359.4-1983, part of AS 1359.30-1987, part of AS 1359.31-1986, AS 1359.32-1974, part of AS 1359.40-1977, AS 1359.60-1986 and AS 1359.69-1974 revised, amalgamated and redesignated AS 1359.101-1997.
| AS 1359.106-1996 | Rotating electrical machines - General requirements Methods of cooling (IC Code) |
| AS 2752-1985 | Preferred numbers and their use |
| AS 1359.41-1986 | Rotating electrical machines - General requirements General characteristics |
| AS 1852.00-1980 | International electrotechnical vocabulary - General index |
| AS 2768-1985 | Electrical insulating materials - Evaluation and classification based on thermal endurance |
| AS 1046.1-1978 | Letter symbols for use in electrotechnology General |
| AS 1359.20-1980 | Rotating electrical machines - General requirements - Classification of types of enclosure |
| AS 1046.4-1991 | Letter symbols for use in electrotechnology - Symbols for quantities to be used for rotating electrical machines |
| AS 1359.102.1-1997 | Rotating electrical machines - General requirements Methods for determining losses and efficiency - General |
| AS/NZS 61058.1:2008 | Switches for appliances General requirements (IEC 61058-1, Ed. 3.1 (2000), MOD) |
| AS/NZS 60079.0:2008 | Explosive atmospheres Equipment - General requirements |
| AS 2941-2002 | Fixed fire protection installations - Pumpset systems |
| AS 60947.4.1-2004 | Low-voltage switchgear and controlgear Contactors and motor-starters - Electromechanical contactors and motor-starters |
| AS 60947.6.2-2004 | Low-voltage switchgear and controlgear Multiple function equipment - Control and protective switching devices (or equipment) (CPS) |
| AS 1359.30-1997 | Rotating electrical machines - General requirements - Preferred outputs and frame sizes |
| AS/NZS 2290.1:2005 | Electrical equipment for coal mines - Introduction and maintenance - For hazardous areas |
| AS 61400.21-2006 | Wind turbines - Measurement and assessment of power quality characteristics of grid connected wind turbines |
| AS 60947.4.2-2004 | Low-voltage switchgear and controlgear Contactors and motor-starters - A.C. semiconductor motor controllers and starters |
| AS/NZS 3800:2005 | Electrical equipment for explosive atmospheres - Repair and overhaul |
| AS/NZS 61058.1:2002 | Switches for appliances General requirements (IEC 61058.1:2000 MOD) |
| AS 2941-2008 | Fixed fire protection installations - Pumpset systems |
| AS 61400.2(INT)-2006 | Wind turbines Design requirements for small wind turbines |
| AS/NZS 3000:2007 | Electrical installations (known as the Australian/New Zealand Wiring Rules) |
| AS 2067-2008 | Substations and high voltage installations exceeding 1 kV a.c. |
| AS/NZS 60079.1:2005 | Electrical apparatus for explosive gas atmospheres Flameproof enclosures 'd' |
| AS 60204.11-2006 | Safety of machinery - Electrical equipment of machines Requirements for HV equipment for voltages above 1000 V a.c. or 1500 V d.c and not exceeding 36 kV (IEC 60204-11, Ed. 1.0 (2000) MOD) |
| AS/NZS 1359.5:2000 | Rotating electrical machines - General requirements Three-phase cage induction motors - High efficiency and minimum energy performance standards requirements |
| AS 2941-2013 | Fixed fire protection installations - Pumpset systems |
| AS/NZS 3947.4.2:2000 | Low-voltage switchgear and controlgear Contactors and motor-starters - A.C. semiconductor motor controllers and starters |
| AS 60204.1-2005 | Safety of machinery - Electrical equipment of machines General requirements (IEC 60204-1, Ed. 5 (FDIS) MOD) |
| AS/NZS 1359.5:2004 | Rotating electrical machines - General requirements Three-phase cage induction motors - High efficiency and minimum energy performance standards requirements |
| AS 61800.1-2007 | Adjustable speed electrical power drive systems General requirements - Rating specifications for low voltage adjustable speed d.c. power drive systems (Reconfirmed 2016) |
| AS 1359.114-1997 | Rotating electrical machines - General requirements - Vibration measurements and limits |
| AS 2067:2016 | Substations and high voltage installations exceeding 1 kV a.c. |
| AS 1359.31-1997 | Rotating electrical machines - General requirements Three-phase induction motors - Operation on unbalanced voltages |
| AS 61800.2-2004 | Adjustable speed electrical power drive systems General requirements - Rating specifications for low voltage adjustable frequency a.c. power drive systems (Reconfirmed 2016) |
| AS 1418.4-2004 | Cranes, hoists and winches Tower cranes |
| AS/NZS 60079.7:2006 | Explosive atmospheres Equipment protection by increased safety 'e' |
| AS 1359.102.1-1997 | Rotating electrical machines - General requirements Methods for determining losses and efficiency - General |
| AS/NZS 60079.15:2006 | Electrical apparatus for explosive gas atmospheres Construction, test and marking of type of protection, n electrical apparatus |
| AS 2650-2005 | Common specifications for high-voltage switchgear and controlgear standards (IEC 60694 Ed.2.2(2002) MOD) |
| AS/NZS 3947.4.1:2001 | Low-voltage switchgear and controlgear Contactors and motor-starters - Electromechanical contactors and motor-starters |
| AS 1359.109-1998 | Rotating electrical machines - General requirements - Noise limits |
| AS 1418.4-2001 | Cranes (including hoists and winches) - Tower cranes |
| AS/NZS 3947.6.2:2001 | Low-voltage switchgear and controlgear Multiple function equipment - Control and protective switching devices (or equipment) (CPS) |
| AS 1418.6-2004 | Cranes, hoists and winches Guided storing and retrieving appliances (Reconfirmed 2018) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.