API 582 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WELDING GUIDELINES FOR THE CHEMICAL, OIL, AND GAS INDUSTRIES
Available format(s)
Hardcopy , PDF
Superseded date
20-05-2023
Superseded by
Language(s)
English
Published date
01-05-2016
Publisher
1 Scope
2 Normative References
3 Definitions
4 General Welding Requirements
5 Welding Processes
6 Welding Consumables (Filler Metal and Flux)
7 Shielding and Purging Gases
8 Preheating and Interpass Temperature
9 Post-weld Heat Treatment (PWHT)
10 Cleaning and Surface Preparation
11 Special Procedure Qualification Requirements/Testing
12 Other Items
Annex A (informative) - Welding Consumables for Shielded
Metal Arc Welding (SMAW)
Annex B (normative) - Weld Overlay and Clad Restoration
(Back Cladding)
Specifies supplementary guidelines and practices for welding and welding related topics for shop and field fabrication, repair and modification of the following: a) pressure-containing equipment such as pressure vessels, heat exchangers, piping, heater tubes, and pressure boundaries of rotating equipment and attachments welded thereto; b) tanks and attachments welded thereto; c) nonremovable internals for process equipment; d) structural items attached and related to process equipment; e) other equipment or component item when referenced by an applicable purchase document.
| DevelopmentNote |
Russian translation of 2ED 2009 edition is still available, see API 582 RUSSIAN. (05/2016)
|
| DocumentType |
Standard
|
| Pages |
38
|
| ProductNote |
This product is unavailable in Cuba, Iran, North Korea, Syria
|
| PublisherName |
American Petroleum Institute
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| API 934-E : 2018 | RECOMMENDED PRACTICE FOR MATERIALS AND FABRICATION OF 1[1/4]CR-[1/2]MO STEEL PRESSURE VESSELS FOR SERVICE ABOVE 825 DEGREES F (440 DEGREES C) |
| API 2009 : 2002 : R2007 | SAFE WELDING, CUTTING, AND HOT WORK PRACTICES IN THE PETROLEUM AND PETROCHEMICAL INDUSTRIES |
| API 585 : 2014 | PRESSURE EQUIPMENT INTEGRITY INCIDENT INVESTIGATION |
| API 620 CHINESE : 2013 | DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS |
| API 2201 : 2003 : R2010 | SAFE HOT TAPPING PRACTICES IN THE PETROLEUM AND PETROCHEMICAL INDUSTRIES |
| API 577 : 2013 | WELDING PROCESSES, INSPECTION, AND METALLURGY |
| ASME PTB 2 : 2009 | GUIDE TO LIFE CYCLE MANAGEMENT OF PRESSURE EQUIPMENT INTEGRITY |
| NACE 8X194 : 2006 | MATERIALS AND FABRICATION PRACTICES FOR NEW PRESSURE VESSELS USED IN WET H[2]S REFINERY SERVICE |
| API 932B : 2012 | DESIGN, MATERIALS, FABRICATION, OPERATION, AND INSPECTION GUIDELINES FOR CORROSION CONTROL IN HYDROPROCESSING REACTOR EFFLUENT AIR COOLER (REAC) SYSTEMS |
| API 571 REDLINE : 2011 | DAMAGE MECHANISMS AFFECTING FIXED EQUIPMENT IN THE REFINING INDUSTRY |
| API 934-A : 2008 | MATERIALS AND FABRICATION OF 2 [1/4]CR-1MO, 2 [1/4]CR-1MO-[1/4]V, 3CR-1MO, AND 3CR-1MO-[1/4]V STEEL HEAVY WALL PRESSURE VESSELS FOR HIGH-TEMPERATURE, HIGH-PRESSURE HYDROGEN SERVICE |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| API 945:2003 | AVOIDING ENVIRONMENTAL CRACKING IN AMINE UNITS |
| API RP 2201 : 2003 | SAFE HOT TAPPING PRACTICES IN THE PETROLEUM AND PETROCHEMICAL INDUSTRIES |
| API TR 938-C REDLINE : 2011 | USE OF DUPLEX STAINLESS STEELS IN THE OIL REFINING INDUSTRY |
| API 584 : 2014 | INTEGRITY OPERATING WINDOWS |
| API TR 938-C : 2015 | USE OF DUPLEX STAINLESS STEELS IN THE OIL REFINING INDUSTRY |
| API 650 : 2013 | WELDED TANKS FOR OIL STORAGE |
| API 1626 REDLINE : 2010 | STORING AND HANDLING ETHANOL AND GASOLINE-ETHANOL BLENDS AT DISTRIBUTION TERMINALS AND FILLING STATIONS |
| API 571 : 2011 | DAMAGE MECHANISMS AFFECTING FIXED EQUIPMENT IN THE REFINING INDUSTRY |
| API TR 934-B : 2011 | FABRICATION CONSIDERATIONS FOR VANADIUM-MODIFIED CR-MO STEEL HEAVY WALL PRESSURE VESSELS |
| API 2009 : 2002 | SAFE WELDING, CUTTING, AND HOT WORK PRACTICES IN THE PETROLEUM AND PETROCHEMICAL INDUSTRIES |
| API TR 934-G : 2016 | DESIGN, FABRICATION, OPERATIONAL EFFECTS, INSPECTION, ASSESSMENT, AND REPAIR OF COKE DRUMS AND PERIPHERAL COMPONENTS IN DELAYED COKING UNITS |
| API 970 : 2017 | CORROSION CONTROL DOCUMENTS |
| API 620 : 2013 | DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS |
| API 510 CHINESE : 2014 | PRESSURE VESSEL INSPECTION CODE: IN-SERVICE INSPECTION, RATING, REPAIR, AND ALTERATION |
| API 620 REDLINE : 2008 | DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS |
| API 939-E : 2013 | IDENTIFICATION, REPAIR, AND MITIGATION OF CRACKING OF STEEL EQUIPMENT IN FUEL ETHANOL SERVICE |
| API 1626 : 2010 | STORING AND HANDLING ETHANOL AND GASOLINE-ETHANOL BLENDS AT DISTRIBUTION TERMINALS AND FILLING STATIONS |
| API 650 : 2013+ADD 3 : 2018 | WELDED TANKS FOR OIL STORAGE |
| API 650 CHINESE : 2013 | WELDED TANKS FOR OIL STORAGE |
| API 945 : 2003 : R2008 | AVOIDING ENVIRONMENTAL CRACKING IN AMINE UNITS |
| NACE SP 01 14 : 2014 | REFINERY INJECTION AND PROCESS MIX POINTS |
| API 510 : 2014 | PRESSURE VESSEL INSPECTION CODE: IN-SERVICE INSPECTION, RATING, REPAIR, AND ALTERATION |
| API 751 : 2013 | SAFE OPERATION OF HYDROFLUORIC ACID ALKYLATION UNITS |
| API 577 CHINESE : 2013 | WELDING PROCESSES, INSPECTION AND METALLURGY |
| API 934-C : 2008 | MATERIALS AND FABRICATION OF 1 [1/4]CR-[1/2]MO STEEL HEAVY WALL PRESSURE VESSELS FOR HIGH-PRESSURE HYDROGEN SERVICE OPERATING AT OR BELOW 825 DEGREES F (441 DEGREES C) |
| API STD 620:2013+ADD3:2021 | Design and Construction of Large, Welded, Low-Pressure Storage Tanks; Twelfth Edition |
| PIP PNSC0001 : 2014 | ASME B31.3 METALLIC PIPING FABRICATION AND EXAMINATION SPECIFICATION |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| ASTM A 923 : 2014 : REDLINE | Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| API 934-C : 2008 | MATERIALS AND FABRICATION OF 1 [1/4]CR-[1/2]MO STEEL HEAVY WALL PRESSURE VESSELS FOR HIGH-PRESSURE HYDROGEN SERVICE OPERATING AT OR BELOW 825 DEGREES F (441 DEGREES C) |
| ASTM E 562 : 2011 : REDLINE | Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count |
| AWS D10.8 : 1996 | RECOMMENDED PRACTICES FOR WELDING OF CHROMIUM-MOLYBDENUM STEEL PIPING AND TUBING |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| AWS A4.2M : 2006 | STANDARD PROCEDURES FOR CALIBRATING MAGNETIC INSTRUMENTS TO MEASURE THE DELTA FERRITE CONTENT OF AUSTENITIC AND DUPLEX FERRITIC-AUSTENITIC STAINLESS STEEL WELD METAL |
| ASME B31.3:2016 | PROCESS PIPING |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| API 510 : 2014 | PRESSURE VESSEL INSPECTION CODE: IN-SERVICE INSPECTION, RATING, REPAIR, AND ALTERATION |
| ASTM A 578/A578M : 2017 : REDLINE | Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications |
| AWS A4.3 : 1993 | DETERMINATION OF THE DIFFUSIBLE HYDROGEN CONTENT OF MARTENSITIC, BAINITIC, AND FERRITIC STEEL WELD METAL PRODUCED BY ARC WELDING |
| NACE SP 04 72 : 2015 | METHODS AND CONTROLS TO PREVENT IN-SERVICE ENVIRONMENTAL CRACKING OF CARBON STEEL WELDMENTS IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS |
| AWS D1.6/D1.6M : 2007 | STRUCTURAL WELDING CODE - STAINLESS STEEL |
| AWS A4.4M : 2001 | STANDARD PROCEDURES FOR DETERMINATION OF MOISTURE CONTENT OF WELDING FLUXES AND WELDING ELECTRODE FLUX COVERINGS |
| ASME PV CODE 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF POWER BOILERS |
| API 934-A : 2008 | MATERIALS AND FABRICATION OF 2 [1/4]CR-1MO, 2 [1/4]CR-1MO-[1/4]V, 3CR-1MO, AND 3CR-1MO-[1/4]V STEEL HEAVY WALL PRESSURE VESSELS FOR HIGH-TEMPERATURE, HIGH-PRESSURE HYDROGEN SERVICE |
| API 934-E : 2010 | RECOMMENDED PRACTICE FOR MATERIALS AND FABRICATION OF 1[1/4]CR-[1/2]MO STEEL PRESSURE VESSELS FOR SERVICE ABOVE 825 DEGREES F (440 DEGREES C) |
| AWS A5.32/A5.32M : 2011 | WELDING CONSUMABLES - GASES AND GAS MIXTURES FOR FUSION WELDING AND ALLIED PROCESSES |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
| AWS A3.0M/A3.0 : 2010 | STANDARD WELDING TERMS AND DEFINITIONS INCLUDING TERMS FOR ADHESIVE BONDING, BRAZING, SOLDERING, THERMAL CUTTING, AND THERMAL SPRAYING |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Are you sure?
Logging out.