A-A-59950 Base Document:2014
NA
Status of Standard is Unknown
Holder, Electrical Card, Wedge Retainers, 7 Body, for Cold Plate Applications, General Requirements for
English
16-05-2014
1. SCOPE
2. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN)
3. SALIENT CHARACTERISTICS
4. REGULATORY REQUIREMENTS
5. PRODUCT CONFORMANCE PROVISIONS
6. PACKAGING
7. NOTES
Specifies the general requirements for a family of 7 piece wedge card holders for holding circuit card assemblies (CCA) into their installed positions when used in heat sinking devices (cold plates, heat exchanger) or other applications.
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
NA
|
This commercial item description (CID) covers the general requirements for a family of 7 piece wedge card holders for holding circuit card assemblies (CCA) into their installed positions when used in heat sinking devices (cold plates, heat exchanger) or other applications. Card holders covered by this CID are intended to provide maximum contact between thermal paths on the circuit card assemblies to the heat sink surfaces, and to provide increased resistance to loosening due to shock and vibration. Requirements for specific card holders are covered in the individual CID specification sheets. Card holders covered by this CID are intended for commercial/industrial applications.
| MIL-HDBK-1861 Revision B:2013 | Selection and Use1 of Electrical and Electronic Assemblies, Boards, Cards, and Associated Hardware |
| A-A-59950-3 Base Document:2014 | Holder, Electrical Card, Wedge Retainers, 7 Piece, for Cold Plate Applications, .250 X .260 Inch (6.35 X 6.60 mm) Body Size, Screw Actuated Shaft |
| A-A-59950-4 Base Document:2014 | Holder, Electrical Card, Wedge Retainers, 7 Piece, for Cold Plate Applications, .250 X .260 Inch (6.35 X 6.60 mm) Body Size, Screw Actuated Shaft, with Visual Lock Indication |
| A-A-59950-1 Base Document:2014 | Holder, Electrical Card, Wedge Retainers, 7 Piece, for Cold Plate Applications, .225 X .225 Inch (5.72 X 5.72 mm) Body Size, Screw Actuated Shaft |
| A-A-59950-2 Base Document:2014 | Holder, Electrical Card, Wedge Retainers, 7 Piece, for Cold Plate Applications, .225 X .225 Inch (5.72 X 5.72 mm) Body Size, Screw Actuated Shaft, with Visual Lock Indication |
| MIL-DTL-5002 Revision E:2011 | Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapons Systems |
| SAE AMSQQA200/8A | Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded A96061 |
| SAE AMSQQN290C | Nickel Plating (Electrodeposited) |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| SAE AMS5904B | Steel, Corrosion-Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| SAE AMSQQS763D | Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| ASTM B 194 : 2015 : REDLINE | Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
| SAE AMS2700E | Passivation of Corrosion Resistant Steels |
| MIL-DTL-18240 Revision F:1997 | Fastener Element, Self-Locking, Threaded Fastener, 250 Degrees F Maximum |
| SAE AMSC26074D | Electroless Nickel Coatings |
| MIL-PRF-46010 Revision H:2013 | Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting NATO Code - S-1738 |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.