17/30356728 DC : 0
NA
Status of Standard is Unknown
BS EN 12261 - GAS METERS - TURBINE GAS METERS
Hardcopy , PDF
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Meter classification
5 Metrological performance requirements
6 Design and material requirements
7 Meter output
8 Marking
9 Documentation
Annex A (normative) - Test facility specifications
Annex B (normative) - Perturbation testing
Annex C (informative) - Recommendations for use
Annex D (normative) - Individual factory testing
Annex E (normative) - Metrological requirements
and tests for each meter prior to
dispatch (Individual meter testing)
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 2014/32/EU
Measuring Instruments Directive
aimed to be covered
Bibliography
BS EN 12261.
| Committee |
GSE/25
|
| DocumentType |
Draft
|
| Pages |
58
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 12261 : DRAFT 2017 | Identical |
| IEC 62246-1:2015 | Reed switches - Part 1: Generic specification |
| OIML D 11 : 2013 | GENERAL REQUIREMENTS FOR MEASURING INSTRUMENTS - ENVIRONMENTAL CONDITIONS |
| ISO 5168:2005 | Measurement of fluid flow — Procedures for the evaluation of uncertainties |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 62246-1:2015 | Reed switches - Part 1: Generic specification |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 12405 : 2002 | GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| EN 60947-5-6:2000 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 60947-5-6:1999 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.