17/30348949 DC : 0
NA
NA
Status of Standard is Unknown
BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
Available format(s)
Hardcopy , PDF
Language(s)
English
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specifications and documentation
5 Constituent products
6 Preparation
7 Welding
8 Mechanical fastening and adhesive
bonding
9 Erection
10 Surface treatment
11 Geometrical tolerances
12 Inspection, testing and corrections
Annex A (normative) - Required additional
information, options to be specified and
requirements for execution classes
Annex B (informative) - Checklist for the content of a
quality plan
Annex C (normative) - Cruciform weld test
Annex D (normative) - Procedure for determination of
slip factor
Annex E (informative) - Surface treatment
Annex F (normative) - Geometrical tolerances -
Essential tolerances
Annex G (normative) - Geometrical tolerances - Functional
tolerances
Annex H (normative) - Geometrical tolerances -
Shell structures
Annex I (informative) - Designation of requirements to
welds on drawings
Annex J (informative) - Recommendations for description
of site conditions and erection in the
execution specification
Annex K (informative) - Guide for preparation of
the execution specification for quality
requirements of welds
Annex L (informative) - Guide for specification of
quality requirements for components and
structures in SC2
Annex M (informative) - Chart for development and use of
a welding procedure specification (WPS)
Annex N (informative) - Weld studs connected by
arc stud welding with tip ignition
Bibliography
BS EN 1090-3.
| Committee |
B/525/9
|
| DocumentType |
Draft
|
| Pages |
127
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 1090-3 : DRAFT 2017 | Identical |
| EN ISO 1479:2011 | Hexagon head tapping screws (ISO 1479:2011) |
| ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) |
| ISO 8839:1986 | Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals |
| ISO 25239-5:2011 | Friction stir welding Aluminium Part 5: Quality and inspection requirements |
| ISO 7599:2010 | Anodizing of aluminium and its alloys General specifications for anodic oxidation coatings on aluminium |
| EN ISO 15981:2002 | Open end blind rivets with break pull mandrel and protruding head - AIA/AIA (ISO 15981:2002) |
| ISO 9018:2015 | Destructive tests on welds in metallic materials Tensile test on cruciform and lapped joints |
| ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
| EN 14399-8:2007 | High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies |
| EN ISO 6520-1:2007 | Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 1: Fusion welding (ISO 6520-1:2007) |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN ISO 17663:2009 | Welding - Quality requirements for heat treatment in connection with welding and allied processes (ISO 17663:2009) |
| ISO 7090:2000 | Plain washers, chamfered Normal series Product grade A |
| EN ISO 8062-1:2007 | Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary (ISO 8062-1:2007) |
| EN ISO 8062-3 : 2007 COR 2009 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 3: GENERAL DIMENSIONAL AND GEOMETRICAL TOLERANCES AND MACHINING ALLOWANCES FOR CASTINGS |
| EN ISO 15481:1999 | Cross recessed pan head drilling screws with tapping screw thread (ISO 15481:1999) |
| EN 485-1:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery |
| EN ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2005) |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| EN 1337-6:2004 | Structural bearings - Part 6: Rocker bearings |
| EN 755-1:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery |
| EN ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012) |
| ISO 13918:2008 | Welding Studs and ceramic ferrules for arc stud welding |
| EN 754-3:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form |
| ISO 15974:2000 | Closed end blind rivets with break pull mandrel and countersunk head AlA/St |
| ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread |
| EN ISO/IEC 17024:2012 | Conformity assessment - General requirements for bodies operating certification of persons (ISO/IEC 17024:2012) |
| EN ISO 7049:2011 | Cross-recessed pan head tapping screws (ISO 7049:2011) |
| ISO 6520-1:2007 | Welding and allied processes Classification of geometric imperfections in metallic materials Part 1: Fusion welding |
| EN 754-7:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form |
| ISO 1479:2011 | Hexagon head tapping screws |
| EN ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) |
| EN ISO 7091:2000 | Plain washers - Normal series - Product grade C (ISO 7091:2000) |
| EN 755-5:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN ISO 6789:2003 | Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003) |
| EN ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012) |
| EN 1301-1:2008 | Aluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery |
| ISO 13920:1996 | Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN ISO 7093-2:2000 | Plain washers - Large series - Part 2: Product grade C (ISO 7093-2:2000) |
| ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts — Property classes 5, 8, 10 and 12 |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 10042:2005 | Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN 573-2:1994 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 2: Chemical symbol based designation system |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| ISO 10642:2004 | Hexagon socket countersunk head screws |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 4288:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996) |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 755-9:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form |
| EN ISO 25239-5:2011 | Friction stir welding - Aluminium - Part 5: Quality and inspection requirements (ISO 25239-5:2011) |
| ISO 4016:2011 | Hexagon head bolts Product grade C |
| ISO 25239-3:2011 | Friction stir welding Aluminium Part 3: Qualification of welding operators |
| EN ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements (ISO 3834-4:2005) |
| EN ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012) |
| ISO 14732:2013 | Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
| EN ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15977:2002) |
| ISO 4034:2012 | Hexagon regular nuts (style 1) Product grade C |
| EN ISO 1481:2011 | Slotted pan head tapping screws (ISO 1481:2011) |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| EN 755-3:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form |
| ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
| EN ISO 7090:2000 | Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000) |
| ISO 17123-7:2005 | Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 7: Optical plumbing instruments |
| ISO 10509:2012 | Hexagon flange head tapping screws |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| ISO 14731:2006 | Welding coordination Tasks and responsibilities |
| EN ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012) |
| ISO 9017:2001 | Destructive tests on welds in metallic materials Fracture test |
| ISO 25239-2:2011 | Friction stir welding Aluminium Part 2: Design of weld joints |
| EN 755-8:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 1396:2015 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| ISO 7976-2:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points |
| ISO 17663:2009 | Welding — Quality requirements for heat treatment in connection with welding and allied processes |
| EN ISO 2009:2011 | Slotted countersunk flat head screws - Product grade A (ISO 2009:2011) |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 755-4:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| EN ISO 7093-1:2000 | Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000) |
| ISO 4017:2014 | Fasteners Hexagon head screws Product grades A and B |
| ISO/TS 8062-2:2013 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules |
| ISO 25239-4:2011 | Friction stir welding Aluminium Part 4: Specification and qualification of welding procedures |
| EN ISO 4016:2011 | Hexagon head bolts - Product grade C (ISO 4016:2011) |
| EN ISO 4014:2011 | Hexagon head bolts - Product grades A and B (ISO 4014:2011) |
| EN ISO 14732:2013 | Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013) |
| ISO 4032:2012 | Hexagon regular nuts (style 1) — Product grades A and B |
| ISO 18273:2015 | Welding consumables Wire electrodes, wires and rods for welding of aluminium and aluminium alloys Classification |
| EN 586-3:2001 | Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form |
| ISO 9013:2017 | Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances |
| EN 755-7:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN ISO 9018:2015 | Destructive tests on welds in metallic materials - Tensile test on cruciform and lapped joints (ISO 9018:2015) |
| ISO 17123-3:2001 | Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 3: Theodolites |
| ISO 15481:1999 | Cross recessed pan head drilling screws with tapping screw thread |
| EN 1337-8:2007 | Structural bearings - Part 8: Guide Bearings and Restraint Bearings |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| EN 1301-3:2008 | Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions |
| ISO 17640:2017 | Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment |
| EN 754-6:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| ISO 3452-1:2013 | Non-destructive testing Penetrant testing Part 1: General principles |
| EN 755-6:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form |
| ISO 4762:2004 | Hexagon socket head cap screws |
| EN 1337-11:1997 | Structural bearings - Part 11: Transport, storage and installation |
| ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head — AIA/St |
| EN ISO 25239-4:2011 | Friction stir welding - Aluminium - Part 4: Specification and qualification of welding procedures (ISO 25239-4:2011) |
| EN ISO 4018:2011 | Hexagon head screws - Product grade C (ISO 4018:2011) |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| EN ISO 13920:1996 | Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996) |
| EN ISO 17639:2013 | Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2003) |
| ISO 15978:2002 | Open end blind rivets with break pull mandrel and countersunk head — AIA/St |
| ISO 1481:2011 | Slotted pan head tapping screws |
| ISO 7089:2000 | Plain washers Normal series Product grade A |
| ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality requirements |
| ISO 8062-1:2007 | Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN ISO 15974:2000 | Closed end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15974:2000) |
| ISO 4463-1:1989 | Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria |
| ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts — Property classes 5, 8 and 10 |
| ISO 15973:2000 | Closed end blind rivets with break pull mandrel and protruding head AlA/St |
| ISO 2009:2011 | Slotted countersunk flat head screws Product grade A |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| ISO 7091:2000 | Plain washers Normal series Product grade C |
| EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| EN ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012) |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| ISO 17639:2003 | Destructive tests on welds in metallic materials Macroscopic and microscopic examination of welds |
| ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread — Property classes 8, 10 and 12 |
| EN ISO 2553:2013 | Welding and allied processes - Symbolic representation on drawings - Welded joints (ISO 2553:2013) |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| EN 515:2017 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread — Property classes 6, 8 and 10 |
| EN 754-5:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form |
| ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) — Property classes 5, 8 and 10 |
| EN ISO 7046-2:2011 | Countersunk flat head screws (common head style) with type H or type Z cross recess - Product grade A - Part 2: Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws (ISO 7046-2:2011) |
| EN ISO 18273:2015 | Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification (ISO 18273:2015) |
| EN 1337-3:2005 | Structural bearings - Part 3: Elastomeric bearings |
| EN ISO 14731:2006 | Welding coordination - Tasks and responsibilities (ISO 14731:2006) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 586-1:1997 | Aluminium and aluminium alloys - Forgings - Part 1: Technical conditions for inspection and delivery |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| EN ISO 4017:2014 | Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014) |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 1090-2:2008+A1:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| ISO/IEC 17024:2012 | Conformity assessment — General requirements for bodies operating certification of persons |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 7976-1:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments |
| ISO 6789:2003 | Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure |
| EN 12206-1:2004 | Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1: Coatings prepared from coating powder |
| EN 14399-7:2007 | High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies |
| EN ISO 4032:2012 | Hexagon regular nuts (style 1) - Product grades A and B (ISO 4032:2012) |
| PREN 1090-5 : DRAFT 2014 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED ALUMINIUM ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| ISO 7093-2:2000 | Plain washers Large series Part 2: Product grade C |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN ISO 25239-3:2011 | Friction stir welding - Aluminium - Part 3: Qualification of welding operators (ISO 25239-3:2011) |
| EN ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999) |
| EN 1559-4:2015 | Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings |
| ISO 17123-4:2012 | Optics and optical instruments — Field procedures for testing geodetic and surveying instruments — Part 4: Electro-optical distance meters (EDM measurements to reflectors) |
| EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
| EN 28839:1991 | Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986) |
| EN ISO 9013:2017 | Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017) |
| ISO 17123-1:2014 | Optics and optical instruments — Field procedures for testing geodetic and surveying instruments — Part 1: Theory |
| EN ISO 7089:2000 | Plain washers - Normal series - Product grade A (ISO 7089:2000) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| EN 1337-5:2005 | Structural bearings - Part 5: Pot bearings |
| EN ISO 15973:2000 | Closed end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15973:2000) |
| ISO 15981:2002 | Open end blind rivets with break pull mandrel and protruding head — AIA/AIA |
| EN ISO 15978:2002 | Open end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15978:2002) |
| EN 754-4:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form |
| ISO 7046-2:2011 | Countersunk flat head screws (common head style) with type H or type Z cross recess Product grade A Part 2: Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws |
| EN ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012) |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| EN ISO 17659:2004 | Welding - Multilingual terms for welded joints with illustrations (ISO 17659:2002) |
| ISO 17659:2002 | Welding — Multilingual terms for welded joints with illustrations |
| EN ISO 25239-2:2011 | Friction stir welding - Aluminium - Part 2: Design of weld joints (ISO 25239-2:2011) |
| EN 573-1:2004 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system |
| ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials Part 3: Standard quality requirements |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 15088:2005 | Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery |
| EN 12020-1:2008 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery |
| EN ISO 4762:2004 | Hexagon socket head cap screws (ISO 4762:2004, Corrected version 2024-08) |
| EN 14399-2:2015 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| ISO 4014:2011 | Hexagon head bolts Product grades A and B |
| ISO 4018:2011 | Hexagon head screws Product grade C |
| ISO 7093-1:2000 | Plain washers Large series Part 1: Product grade A |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.