15/30316975 DC : 0
NA
NA
Status of Standard is Unknown
BS EN 1504-2 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 2: SURFACE PROTECTION SYSTEMS FOR CONCRETE
Available format(s)
Hardcopy , PDF
Language(s)
English
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance characteristics for intended uses
5 Product characteristics
6 Sampling
7 Assessment and verification of the constancy
of performance - AVCP
8 Marking and labelling
Annex A (informative) - Minimum frequency of testing
for factory production control
Annex B (informative) - Examples of the application of
the classification system in different cases
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Regulation
Bibliography
BS EN 1504-2.
| Committee |
B/517/8
|
| DocumentType |
Draft
|
| Pages |
50
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 1504-2 : DRAFT 2015 | Identical |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| EN ISO 4628-2:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering (ISO 4628-2:2016) |
| EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
| EN 13578:2003 | Products and systems for the protection and repair of concrete structure - Test Method - Compatibility on wet concrete |
| EN 13687-3:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 3: Thermal cycling without de-icing salt impact |
| EN ISO 5470-1:2016 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 1: Taber abrader (ISO 5470-1:2016) |
| EN 13581:2002 | Products and systems for the protection and repair of concrete structures - Test method - Determination of loss of mass of hydrophobic impregnated concrete after freeze-thaw salt stress |
| ISO 3451-1:2008 | Plastics Determination of ash Part 1: General methods |
| EN 13529:2003 | Products and systems for the protection and repair of concrete structures - Test methods - Resistance to severe chemical attack |
| EN 12190:1998 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of compressive strength of repair mortar |
| EN 13687-5:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 5: Resistance to temperature shock |
| EN ISO 2431:2011 | Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011) |
| ISO 3219:1993 | Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate |
| ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
| EN 13687-2:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock) |
| EN 13579:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Drying test for hydrophobic impregnation |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN 13580:2002 | Products and systems for the protection and repair of concrete structures - Test Methods - Water absorption and resistance to alkali for hydrophobic impregnations |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| EN 1542:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off |
| EN 1767:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Infrared analysis |
| EN ISO 2811-2:2011 | Paints and varnishes - Determination of density - Part 2: Immersed body (plummet) method (ISO 2811-2:2011) |
| EN 13395-2:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 2: Test for flow of grout or mortar |
| EN 13036-4:2011 | Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| EN 1015-7:1998 | Methods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar |
| EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
| EN ISO 9514:2005 | Paints and varnishes - Determination of the pot life of multicomponent coating systems - Preparation and conditioning of samples and guidelines for testing (ISO 9514:2005) |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN ISO 4628-4:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 4: Assessment of degree of cracking (ISO 4628-4:2016) |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| EN ISO 2811-1:2016 | Paints and varnishes - Determination of density - Part 1: Pycnometer method (ISO 2811-1:2016) |
| EN 14306:2015 | Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
| EN 1877-2:2000 | Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 2: Determination of amine functions using the total basicity number |
| ISO 4628-4:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of cracking |
| EN 1240:2011 | Adhesives - Determination of hydroxyl value and/or hydroxyl content |
| EN ISO 9239-1:2010 | Reaction to fire tests for floorings - Part 1: Determination of the burning behaviour using a radiant heat source (ISO 9239-1:2010) |
| ISO 4628-5:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 5: Assessment of degree of flaking |
| EN ISO 7783-1:1999 | Paints and varnishes - Determination of water-vapour transmission rate - Part 1: Dish method for free films (ISO 7783-1:1996, including Technical Corrigendum 1:1998) |
| ISO 390:1993 | Products in fibre-reinforced cement Sampling and inspection |
| ISO 2811-2:2011 | Paints and varnishes Determination of density Part 2: Immersed body (plummet) method |
| ISO 5470-1:2016 | Rubber- or plastics-coated fabrics Determination of abrasion resistance Part 1: Taber abrader |
| EN 1062-6:2002 | Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 6: Determination of carbon dioxide permeability |
| EN 12192-1:2002 | Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 1: Test method for dry components of premixed mortar |
| EN ISO 3219:1994 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| ISO 2815:2003 | Paints and varnishes Buchholz indentation test |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| ISO 6272-1:2011 | Paints and varnishes — Rapid-deformation (impact resistance) tests — Part 1: Falling-weight test, large-area indenter |
| EN ISO 2815:2003 | Paints and varnishes - Buchholz indentation test (ISO 2815:2003) |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| EN 12617-1:2003 | Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Determination of linear shrinkage for polymers and surface protection systems (SPS) |
| EN ISO 7783-2:1999 | Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 2: Determination and classification of water-vapour transmission rate (permeability) (ISO 7783-2:1999) |
| EN 1877-1:2000 | Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 1: Determination of epoxy equivalent |
| EN 1504-1:2005 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions |
| EN 1504-8:2016 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP) |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN ISO 4628-5:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking (ISO 4628-5:2016) |
| EN 1062-3:2008 | Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 3: Determination of liquid water permeability |
| ISO 9239-1:2010 | Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| EN 13687-1:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 1: Freeze-thaw cycling with de-icing salt immersion |
| EN 1766:2017 | Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing |
| ISO 9514:2005 | Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing |
| EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
| EN 1770:1998 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of the coefficient of thermal expansion |
| EN ISO 6272-1:2011 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011) |
| EN 206:2013+A1:2016 | Concrete - Specification, performance, production and conformity |
| EN 1504-9:2008 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 9: General principles for the use of products and systems |
| EN ISO 2808:2007 | Paints and varnishes - Determination of film thickness (ISO 2808:2007) |
| ISO 4628-2:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering |
| EN 13813:2002 | Screed material and floor screeds - Screed material - Properties and requirements |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| EN 1062-7:2004 | Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 7: Determination of crack bridging properties |
| ISO 2431:2011 | Paints and varnishes Determination of flow time by use of flow cups |
| EN 13294:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.