13/30241415 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 15566 - RAILWAY APPLICATIONS - RAILWAY ROLLING STOCK - DRAW GEAR AND SCREW COUPLING
Hardcopy , PDF
31-10-2016
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for all types of draw gear and screw
coupling
5 Draw gear
6 Screw coupling
7 Elastic device
Annex A (informative) - Dynamic test procedure
Annex B (normative) - Draw hook - dimensions
Annex C (normative) - Draw gear - Interface
dimension
Annex D (normative) - Screw coupling components - dimensions
Annex E (normative) - Draw hook and drawbar - Requirements
Annex F (normative) - Screw coupling and component
parts - Requirements
Annex G (normative) - Elastic device - Requirements
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
EU Directive 2008/57/EC of the European Parliament
and of the Council of 17 June 2008 on the
interoperability of the rail system within the
Community (Recast)
Bibliography
BS EN 15566
| Committee |
RAE/3/-/9
|
| DocumentType |
Draft
|
| Pages |
68
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 15566 : DRAFT 2013 | Identical |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 7619-1:2010 | Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness) |
| ISO 4967:2013 | Steel — Determination of content of non-metallic inclusions — Micrographic method using standard diagrams |
| UIC 520 : 7ED 2003 | WAGONS, COACHES AND VANS - DRAW GEAR - STANDARDISATION |
| ISO 815-2:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures |
| EN 10079:2007 | Definition of steel products |
| ISO 813:2016 | Rubber, vulcanized or thermoplastic Determination of adhesion to a rigid substrate 90 degree peel method |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| UIC 827-1 : 2ED 1990 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF ELASTOMER COMPONENTS FOR BUFFERS |
| EN 15085-1:2007+A1:2013 | Railway applications - Welding of railway vehicles and components - Part 1: General |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 15839:2012+A1:2015 | Railway applications - Testing for the acceptance of running characteristics of railway vehicles - Freight wagons - Testing of running safety under longitudinal compressive forces |
| EN 15085-5:2007 | Railway applications - Welding of railway vehicles and components - Part 5: Inspection, testing and documentation |
| EN 10228-1:1999 | Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 7438:2016 | Metallic materials Bend test |
| UIC B51 RP 27 : 1995 | DESIGN AND TESTING OF NEW DRAW GEAR FOR WAGONS |
| UIC 825 : 4ED 1985 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF DRAW HOOKS WITH NOMINAL LOAD EQUAL TO 250 KN, 600 KN OR 1000 KN FOR TRACTIVE AND TRAILING STOCK |
| EN 10021:2006 | General technical delivery conditions for steel products |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| UIC 827-2 : 3ED 1981 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF STEEL RINGS FOR BUFFER SPRINGS |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
| EN 15020:2006+A1:2010 | Railway applications - Rescue coupler - Performance requirements, specific interface geometry and test methods |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 15085-2:2007 | Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer |
| UIC 826 : 3ED 2004 | TECHNICAL PROVISIONS FOR THE SUPPLY OF SCREW COUPLINGS FOR TRACTIVE AND TRAILING STOCK |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| EN 15085-4:2007 | Railway applications - Welding of railway vehicles and components - Part 4: Production requirements |
| ISO 4968:1979 | Steel Macrographic examination by sulfur print (Baumann method) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.