09/30199785 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS 6S 100 - PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT STEELS (OTHER THAN PLATE, SHEET, STRIP AND TUBE)
Hardcopy , PDF
31-03-2010
English
Foreword
Section 1. General requirements
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Information to be supplied by the purchaser
6 Manufacture
7 Heat treatment
8 Chemical composition
9 Product analysis and permitted variations
10 Temporary identification up to the cast approval stage
11 Surface dressing
12 Surface inspection
13 Freedom from defects
14 Sulfur printing and deep etching tests
15 Lead segregation
16 Cleanness
17 Ultrasonic examination
18 Testing
19 Condition of supply
20 Dimensional tolerances
21 Maintenance of identity
22 Final marking
23 Certification
Section 2. Bar for machining delivered in other than the
final heat-treated condition (for parts to be
heat treated after machining)
24 General
25 Selection and preparation of mechanical test samples
26 Mechanical tests
27 Hardness test
Section 3. Bar and rod for machining delivered in the
final heat-treated condition, including austenitic
corrosion resisting steels
28 General
29 Selection and preparation of mechanical test samples
30 Mechanical tests
31 Hardness test
Section 4. Carbon steel bar and rod for machining, not
subject to hardening and tempering
32 General
33 Selection and preparation of mechanical test samples
34 Mechanical tests
Section 5. Forging stock and billet and bar for subsequent
hot working
35 General
36 Selection and preparation of mechanical test samples
37 Mechanical tests
38 Hardness test
39 Surface inspection of forging stock
Section 6. Forgings
40 General
41 Manufacture
42 Pre-production forgings
43 Production forgings
44 Procedure X for process control testing
45 Selection and preparation of mechanical test samples for
batch release testing
46 Mechanical tests
47 Hardness test
Section 7. Parts finally heat treated after machining
48 General
49 Parts for normalizing, hardening and tempering, or softening
50 Parts for carburizing
51 Parts for nitriding
52 Parts for precipitation hardening
Section 8. Bar and rod for the manufacture of forged bolts and
forged nuts only
53 General
54 Manufacture
55 Hardening test
56 Tensile and hardness tests
57 Freedom from carburization and decarburization
58 Freedom from surface defects
59 Non-destructive testing
Section 9. Spring steel rod and wire for springs
60 General
61 Rod for wire drawing
62 Wire for the manufacture of springs
63 Springs manufactured from wire
Annexes
Annex A (normative) - Rules for application of values for
chemical composition and mechanical properties
given in material specifications
Annex B (normative) - Cleanness examination procedure
Annex C (normative) - Ultrasonic examination procedure
Annex D (normative) - Inspection and testing requirements
for springs
BS 6S 100
Committee |
ACE/61
|
DocumentType |
Draft
|
Pages |
66
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
BS EN 2002-2:2005 | Aerospace series. Metallic materials. Test methods Tensile testing at elevated temperature |
BS EN 10017:2004 | Steel rod for drawing and/or cold rolling. Dimensions and tolerances |
BS EN 10059:2003 | Hot rolled square steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
BS EN ISO 642:1999 | Steel hardenability test by end quenching (Jominy test) |
BS EN ISO 6506-1:2014 | Metallic materials. Brinell hardness test Test method |
BS 131-1:1961 | Methods for notched bar tests The Izod impact test on metals |
BS EN ISO 6508-1:2015 | Metallic materials. Rockwell hardness test Test method |
BS EN ISO 6507-1:2005 | Metallic materials. Vickers hardness test Test method |
BS EN 12668-2:2010 | Non-destructive testing. Characterization and verification of ultrasonic examination equipment Probes |
BS EN 10243-1:1999 | Steel die forgings. Tolerances on dimensions Drop and vertical press forgings |
BS EN 12668-1:2010 | Non-destructive testing. Characterization and verification of ultrasonic examination equipment Instruments |
BS 6200-2.1:1993 | Sampling and analysis of iron, steel and other ferrous metals. Sampling and sample preparation Methods for iron and steel |
BS EN 2002-005:2007 | Aerospace series. Test methods for metallic materials Uninterrupted creep and stress-rupture testing |
BS EN ISO 148-2:2016 | Metallic materials. Charpy pendulum impact test Verification of testing machines |
SAE AMS 2301 : 2015 | STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
BS EN 12668-3:2013 | Non-destructive testing. Characterization and verification of ultrasonic examination equipment Combined equipment |
BS EN 4179:2017 | Aerospace series. Qualification and approval of personnel for non-destructive testing |
BS 6285:1982 | Method for the macrographic examination of steel by sulphur print (Baumann method) |
BS EN ISO 643:2012 | Steels. Micrographic determination of the apparent grain size |
SAE AMS 2750 : 2012 | PYROMETRY |
BS EN 10058:2003 | Hot rolled flat steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
BS EN 10218-1:2012 | Steel wire and wire products. General Test methods |
BS EN 10060:2003 | Hot rolled round steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
BS 6533:1984 | Guide to macroscopic examination of steel by etching with strong mineral acids |
BS EN 10061:2003 | Hot rolled hexagon steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
BS 6200-2.2:1993 | Sampling and analysis of iron, steel and other ferrous metals. Sampling and sample preparation Methods for ferroalloys and other alloying additives |
BS EN 10108:2004 | Round steel rod for cold heading and cold extrusion. Dimensions and tolerances |
BS EN 10045-2:1993 | Charpy impact test on metallic materials Method for the verification of impact testing machines |
BS EN 2002-1:2005 | Aerospace series. Metallic materials. Test methods Tensile testing at ambient temperature |
BS EN ISO 3887:2003 | Steels. Determination of depth of decarburization |
BS 5046:1974 | Method for the estimation of equivalent diameters in the heat treatment of steel |
BS 4A 100:2003 | Specification for general requirements for bolts and free running nuts of tensile strength not exceeding 1249 MPa |
BS EN 10243-2:1999 | Steel die forgings. Tolerances on dimensions Upset forgings made on horizontal forging machines |
BS EN 10092-1:2003 | Hot rolled spring steel flat bars Flat bars. Dimensions and tolerances on shape and dimensions |
BS EN 10278:1999 | Dimensions and tolerances of bright steel products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.