07/30164729 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 12999 - CRANES - LOADER CRANES
Hardcopy , PDF
30-04-2011
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 Definitions
3.2 Terminology
4 List of significant hazards
5 Safety requirements and/or safety measures
5.1 General
5.2 Structural calculation
5.3 Stress analysis
5.4 Mechanical arrangements
5.5 Hydraulic system
5.6 Limiting and indicating devices
5.7 Controls
5.8 Control stations
5.9 Electrical systems and related phenomena
5.10 Installation
6 Verification of the safety requirements and/or measures
6.1 General
6.2 Testing and test procedures
7 Information for use
7.1 General
7.2 Manuals
7.3 Marking
Annex A (informative) Examples of configurations and mountings
Annex B (informative) Stress history parameter s and stress
history classes S
Annex C (informative) Explanatory notes
Annex D (informative) Examples of dangerous movements
Annex E (normative) Symbols for working and setting-up
functions
Annex F (informative) Control system - Preferred vertical
layout for controls operated from the
ground
Annex G (informative) Control system - Horizontal layout order
Annex H (informative) Control levers for high seats and remote
controls
Annex I (not used)
Annex J (normative) Minimum internal dimensions for cabins
fitted on vehicle mounted loader cranes up
to a net lifting moment of 250 kNm
Annex K (informative) Examples of raised control stations
Annex L (normative) Raised control stations - Measures
regarding hand rails and hand holds,
ladders and steps
Annex M (informative) Installation of a loader crane on a vehicle
Annex N (informative) Selection of a suitable set of crane
standards for a given application
Annex ZA (informative) Relationship of this document with EC
Directives
Annex ZB (informative) Relationship of this document with EC
Directives
Bibliography
BS EN 12999
| Committee |
MHE/3
|
| DocumentType |
Draft
|
| Pages |
81
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 12999 : DRAFT 2007 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| DIN 15061-1:1977-08 | LIFTING APPLIANCES; GROOVE PROFILES FOR WIRE ROPE SHEAVES |
| EN 12644-2:2000+A1:2008 | Cranes - Information for use and testing - Part 2: Marking |
| ISO 4310:2009 | Cranes — Test code and procedures |
| ISO 5353:1995 | Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 4308-2:1988 | Cranes and lifting appliances Selection of wire ropes Part 2: Mobile cranes Coefficient of utilization |
| ISO 8686-1:2012 | Cranes — Design principles for loads and load combinations — Part 1: General |
| EN 13586:2004+A1:2008 | Cranes - Access |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| ISO 9013:2017 | Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances |
| EN 12644-1:2001+A1:2008 | Cranes - Information for use and testing - Part 1: Instructions |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN ISO 5353:1998 | Earth-moving machinery, and tractors and machinery for agriculture and forestry - Seat index point (ISO 5353:1995) |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| EN 61000-6-4:2007/A1:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| DIN 15400:1990-06 | LIFTING HOOKS - MATERIALS, MECHANICAL PROPERTIES, LIFTING CAPACITY AND STRESSES |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| DIN 15401-2:1983-09 | LIFTING HOOKS FOR LIFTING APPLIANCES - SINGLE HOOKS - FINISHED PARTS WITH THREADED SHANK |
| EN ISO 9013:2017 | Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017) |
| EN 13000:2010+A1:2014 | Cranes - Mobile cranes |
| EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.