I.S. EN 1433:2002
Current
The latest, up-to-date edition.
DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Places of installation for drainage channels
6 Materials
7 Design and manufacturing requirements
8 Marking
9 Testing
10 Evaluation of Conformity
11 Installation
Annex A (normative) - Model procedure of internal quality
control
Annex B (normative) - Supplementary requirements for
concrete products submitted to very severe
freeze-thaw conditions with standing water
containing de-icing salts
Annex C (normative) - Determination of freeze/thaw
resistance with de-icing salt
Annex D (informative) - Inspection control, carried out by
a third party certification body (third party
control)
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU
Construction Products Directive
Bibliography
Provides requirements for linear drainage channels for the channels for the collection and conveyance of surface water when installed within areas subjected to pedestrian and/or vehicular traffic.
| DevelopmentNote |
COR 2004 Issued on 15/08/2010. (09/2010)
|
| DocumentType |
Standard
|
| Pages |
67
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| BS EN 1433:2002 | Equivalent |
| DIN EN 1433:2005-09 | Identical |
| BS EN 1433:2002 | Identical |
| NF EN 1433 : 2003 AMD 1 2005 | Identical |
| NS EN 1433 : 2003 AMD 1 2005 | Identical |
| NEN EN 1433 : 2002 C1 2005 | Identical |
| EN 1433:2002 | Equivalent |
| NBN EN 1433 : 2003 AMD 1 2005 | Identical |
| UNE-EN 1433:2003 | Identical |
| EN 10142 : 2000 | CONTINUOUSLY HOT-DIP ZINC COATED LOW CARBON STEELS SHEET AND STRIP FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS |
| EN 10215 : 1995 | CONTINUOUSLY HOT-DIP ALUMINIUM-ZINC (AZ) COATED STEEL STRIP AND SHEET - TECHNICAL DELIVERY CONDITIONS |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| EN 1170-5:1997 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 5: Measuring bending strength, "Complete bending test" method |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ENV 10080 : 1995 | STEEL FOR THE REINFORCEMENT OF CONCRETE WELDABLE RIBBED REINFORCING STEEL B500 - TECHNICAL DELIVERY CONDITIONS FOR BARS, COILS AND WELDED FABRIC |
| EN 1169:1999 | Precast concrete products - General rules for factory production control of glass-fibre reinforced cement |
| EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
| EN 10214 : 1995 | CONTINUOUSLY HOT-DIP ZINC-ALUMINIUM (ZA) COATED STEEL STRIP AND SHEET - TECHNICAL DELIVERY CONDITIONS |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| ISO 4012:1978 | Concrete — Determination of compressive strength of test specimens |
| ISO 185:2005 | Grey cast irons — Classification |
| ISO 630:1995 | Structural steels — Plates, wide flats, bars, sections and profiles |
| ISO 7500-1:2015 | Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Calibration and verification of the force-measuring system |
| ISO 3755:1991 | Cast carbon steels for general engineering purposes |
| EN 12163:2016 | Copper and copper alloys - Rod for general purposes |
| ISO 8062:1994 | Castings — System of dimensional tolerances and machining allowances |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.