UNI EN 1854 : 2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
Superseded date
08-05-2023
Superseded by
Published date
24-07-2010
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common use
in the various countries
Annex B (informative) - Leak-tightness test - volumetric
method
Annex C (informative) - Leak-tightness test - pressure loss
method
Annex D (informative) - Conversion of pressure loss into
leakage rate
Annex E (normative) - Electrical/electronic component
fault modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories as defined in
EU Directive 97/23/EC
Annex G (normative) - Materials for pressurized parts
Annex H (informative) - Additional materials for pressurized
parts
Annex I (normative) - Requirements for controls used in
DC supplied gas burners and gas burning appliances
Annex AA (informative) - Manufacturers declaration for
EPSDs
Annex ZA (informative) - Clauses of this European Standard
addressing requirements or provisions of EU-Directives
Bibliography
Figures
Tables
Includes the safety, construction and performance requirements for pressure sensing devices.
| Committee |
CT 114
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 1854 : 2010 | Identical |
| NF EN 1854 : 2010 | Identical |
| NS EN 1854 : 2010 | Identical |
| EN 1854:2010 | Identical |
| NBN EN 1854 : 2010 | Identical |
| BS EN 1854:2010 | Identical |
| I.S. EN 1854:2010 | Identical |
| NEN EN 1854 : 2010 | Identical |
| SN EN 1854 : 2010 | Identical |
| DIN EN 1854:2010-10 | Identical |
| UNE-EN 1854:2010 | Identical |
| UNI 663 : 1968 | TUBI SENZA SALDATURA DI ACCIAIO NON LEGATO. TUBI LISCI PER USI GENERICI. QUALITA, PRESCRIZIONI E PROVE. |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ASTM B 85 : 2003 | Standard Specification for Aluminum-Alloy Die Castings |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 274:1975 | Copper tubes of circular section — Dimensions |
| IEC 60191-1:2007 | Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices |
| EN 60730-2-6:2016 | Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
| ISO 7637-3:2016 | Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines |
| DIN 1693 : 1961 | |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| UNI 4894 : 62 AMD 1 90 | LEGHE DI RAME DA LAVORAZIONE PLASTICA. OTTONE BINARIO CON CU 67% E ZN 33%. |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 61000-4-11:2004/A1:2017 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017) |
| EN 12067-2:2004 | Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types |
| EN 175301-803:2006 | Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 1643:2014 | Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves |
| ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| EN 10028-6:2017 | Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered |
| IEC 61000-4-11:2004+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
| EN 60127-1:2006/A2:2015 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
| ISO 1083:2004 | Spheroidal graphite cast irons - Classification |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| SAE J 429 : 2014 | MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS |
| ASTM A 694/A694M : 2016 : REDLINE | Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 12067-1 : 98 AMD 1 2003 | GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES |
| ISO 7637-2:2011 | Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 10087:1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| ASTM A 707/A707M : 2014 : REDLINE | Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service |
| IEC 61000-4-8:2009 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
| IEC 60730-2-6:2015 | Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| UNI 9001-2 : 1987 | ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. GRUPPO ALLUMINIO. AL 99,5 (1050 A). |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 61558-2-17:1997 | Safety of power transformers, power supply units and similar - Part 2-17: Particular requirements for transformers for switch mode power supplies |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV | Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| API 5L : 2012 | LINE PIPE |
| EN 10277-3:2008 | Bright steel products - Technical delivery conditions - Part 3: Free-cutting steels |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| ASTM A 351/A351M : 2016-05 | SPECIFICATION FOR CASTINGS, AUSTENITIC, FOR PRESSURE-CONTAINING PARTS |
| ISO 3506:1979 | Corrosion-resistant stainless steel fasteners — Specifications |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ASTM A 420/A420M : 2016 : REDLINE | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service |
| IEC 61558-2-17:1997 | Safety of power transformers, power supply units and similar - Part2: Particular requirements for transformers for switch mode powersupplies |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| BS 1387:1985 | Specification for screwed and socketed steel tubes and tubulars and for plain end steel tubes suitable for welding or for screwing to BS 21 pipe threads |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN 10028-5:2017 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| BS 2789:1985 | Specification for spheroidal graphite or nodular graphite cast iron |
| EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
| IEC 61643-1:2005 | Low-voltage surge protective devices - Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10250-4:1999 | Open die steel forgings for general engineering purposes - Part 4: Stainless steels |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 126:2012 | Multifunctional controls for gas burning appliances |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| UNI 5705 : 1965 | |
| EN 10250-1:1999 | Open die steel forgings for general engineering purposes - Part 1: General requirements |
| EN 61000-4-8:2010 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| DIN 1630:1984-10 | HIGH PERFORMANCE SEAMLESS CIRCULAR UNALLOYED STEEL TUBES - TECHNICAL DELIVERY CONDITIONS |
| UNI 4892 : 62 AMD 1 90 | LEGHE DI RAME DA LAVORAZIONE PLASTICA. OTTONE BINARIO CON CU 63% E ZN 37%. |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| EN 10250-2:1999 | Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels |
| BS 1490:1988 | Specification for aluminium and aluminium alloy ingots and castings for general engineering purposes |
| ASTM A 217/A217M : 2014 : REDLINE | Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service |
| ISO 65:1981 | Carbon steel tubes suitable for screwing in accordance with ISO 7-1 |
| EN 10213-3 : 1995 | TECHNICAL DELIVERY CONDITIONS FOR STEEL CASTINGS FOR PRESSURE PURPOSES - PART 3: STEEL GRADES FOR USE AT LOW TEMPERATURES |
| EN 10214 : 1995 | CONTINUOUSLY HOT-DIP ZINC-ALUMINIUM (ZA) COATED STEEL STRIP AND SHEET - TECHNICAL DELIVERY CONDITIONS |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| UNI 3158 : 1977 AMD 152 1985 | CAST UNALLOYED QUALITY STEELS FOR GENERAL ENGINEERING PURPOSES - QUALITIES, REQUIREMENTS AND TESTS |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| UNI 7729 : 1984 | TUBI SENZA SALDATURA, CON ESTREMITA LISCE, DI ACCIAIO NON LEGATO DI QUALITA, PER APPLICAZIONI MECCANICHE. |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| UNI 9006-4 : 1987 | ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. LEGHE ALLUMINIO-MAGNESIO-SILICIO. LEGA AL SI 1 MG 0,9 MN 0,7 (6082). |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| EN 1106:2010 | Manually operated taps for gas burning appliances |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| IEC 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| UNI 9006-1 : 1988 | ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. LEGHE ALLUMINIO-MAGNESIO-SILICIO. LEGA AL MG 0,5 SI 0,4 FE 0,2 (6060). |
| UNI 9002-5 : 1989 | ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA - LEGHE ALLUMINIO-RAME - LEGA AL CU 5,5 PB 0,4 BI 0,4 (2011) |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| SAE J 995 : 2012 | MECHANICAL AND MATERIAL REQUIREMENTS FOR STEEL NUTS |
| DIN 2391-2:1994-09 | SEAMLESS PRECISION STEEL TUBES - PART 2: TECHNICAL DELIVERY CONDITIONS |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 257:2010 | Mechanical thermostats for gas-burning appliances |
| EN 12078:1998 | Zero governors for gas burners and gas burning appliances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.