UNI EN 14276-1 : 2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS
Superseded date
09-08-2022
Superseded by
Published date
01-01-2011
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Pressure Vessel classification
6 Design
7 Manufacturing
8 Testing and inspection
Annex A (normative) - Alternative requirements for prevention
of brittle fracture: Method according to temperature
stress cases
Annex B (normative) - Specification and approval of brazing
procedures, brazers and brazing operators
Annex C (normative) - Pressure testing
Annex D (informative) - Relations between the different
pressures
Annex E (normative) - Experimental methods
Annex F (normative) - Material characteristics for design
Annex G (informative) - Component classification in the sense
of the Pressure Equipment Directive (PED)
Annex H (informative) - Selection of module of conformity
Annex I (normative) - Grouping system for materials
Annex J (informative) - DN System
Annex K (normative) - Specification and approval of expansion
procedures and operators
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 97/23/EC
Bibliography
Describes the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 14276-1 : 2006 + A1 2011 | Identical |
| NBN EN 14276-1 : 2006 + A1 2011 | Identical |
| NEN EN 14276-1 : 2006 + A1 2011 | Identical |
| NS EN 14276-1 : 2006 + A1 2011 | Identical |
| I.S. EN 14276-1:2006 | Identical |
| ONORM EN 14276-1 : 2011 | Identical |
| SN EN 14276-1 : 2006 + A1 2011 | Identical |
| UNE-EN 14276-1:2007 | Identical |
| BS EN 14276-1 : 2006 | Identical |
| EN 14276-1:2006+A1:2011 | Identical |
| DIN EN 14276-1:2011-05 | Identical |
| ISO 17672:2016 | Brazing — Filler metals |
| EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| EN 1045:1997 | Brazing - Fluxes for brazing - Classification and technical delivery conditions |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 13445-6 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| EN 378-4:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| CR 13445-7:2002 | Unfired pressure vessels - Part 7: Guidance on the use of the conformity procedures |
| EN ISO 17672:2016 | Brazing - Filler metals (ISO 17672:2016) |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 378-1:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 378-3:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 764-1:2015+A1:2016 | Pressure equipment - Part 1: Vocabulary |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 910 : 1996 | DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS |
| EN 13445-8 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 8: ADDITIONAL REQUIREMENTS FOR PRESSURE VESSELS OF ALUMINIUM AND ALUMINIUM ALLOYS |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 15614-8:2016 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 8: Welding of tubes to tube-plate joints |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 3677:2016 | Filler metal for soldering and brazing - Designation (ISO 3677:2016) |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 7438:2016 | Metallic materials Bend test |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| ISO 3677:2016 | Filler metal for soldering and brazing — Designation |
| EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| EN 12735-1:2016 | Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
| ISO 5187:1985 | Welding and allied processes — Assemblies made with soft solders and brazing filler metals — Mechanical test methods |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 10012:2003 | Measurement management systems — Requirements for measurement processes and measuring equipment |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| ISO 15609-2:2001 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding |
| EN 764-2:2012 | Pressure equipment - Part 2: Quantities, symbols and units |
| EN 12517-1:2006 | Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels |
| EN ISO 10012:2003 | Measurement management systems - Requirements for measurement processes and measuring equipment (ISO 10012:2003) |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| ISO 817:2014 | Refrigerants Designation and safety classification |
| EN ISO 15614-8:2016 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints (ISO 15614-8:2016) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| EN 378-2:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| EN 12451:2012 | Copper and copper alloys - Seamless, round tubes for heat exchangers |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.