UNE-EN 1366-1:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fire resistance tests for service installations - Part 1: Ventilation ducts
Hardcopy , PDF
29-09-2021
Spanish, Castilian, English
28-09-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Test equipment
5 Test conditions
6 Test specimen
7 Installation of test specimen
8 Conditioning
9 Application of instrumentation
10 Test procedure
11 Performance criteria
12 Test report
13 Field of direct application of test results
Annex A (informative) Informative General Guidance
Defines a procedure to determine the fire resistance of horizontal and vertical ventilation ducts under standard fire conditions. For use in conjunction with EN636-1. Excludes fixing of suspension devices to floors or walls, two or three sided ducts, doors of inspection openings, unless included in the duct to be tested, ducts containing fire dampers at points where they pass through fire separations and ducts whose fire resistance is dependent upon the fire resistance performance of a ceiling.
| Committee |
CTN 23
|
| DevelopmentNote |
Supersedes UNE 23766-1 (1998) (07/2003)
|
| DocumentType |
Standard
|
| Pages |
52
|
| PublisherName |
Asociacion Espanola de Normalizacion
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 1366-1 : 2014 | Identical |
| NF EN 1366-1 : 2014 | Identical |
| NBN EN 1366-1 : 2014 | Identical |
| NEN EN 1366-1 : 2014 | Identical |
| NS EN 1366-1 : 2014 | Identical |
| I.S. EN 1366-1:2014 | Identical |
| SN EN 1366-1 : 2014 | Identical |
| UNI EN 1366-1 : 2014 | Identical |
| BS EN 1366-1:2014 | Identical |
| EN 1366-1:2014 | Identical |
| DIN EN 1366-1:2014-12 | Identical |
| ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles |
| EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
| EN ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003) |
| EN 15882-1:2011+A1:2017 | Extended application of results from fire resistance tests for service installations - Part 1: Ducts |
| EN 1364-1:1999 | Fire resistance tests for non-loadbearing elements - Part 1: Walls |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 13943:2017 | Fire safety — Vocabulary |
| EN 12237:2003 | Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
| ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN 1366-8:2004 | Fire resistance tests for service installations - Part 8: Smoke extraction ducts |
| EN 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| EN ISO 13943:2017 | Fire safety - Vocabulary (ISO 13943:2017) |
| EN 1363-1:2012 | Fire resistance tests - Part 1: General Requirements |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 1363-2:1999 | Fire resistance tests - Part 2: Alternative and additional procedures |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.