UL 60335-2-67:1ED 2017-12-22
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Household and Similar Appliances - Safety - Part 2-67: Particular requirements for floor treatment machines, for commercial use
Hardcopy
08-06-2021
English
22-12-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
PREFACE
NATIONAL DIFFERENCES
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirement
5 General conditions for the tests
6 Classification
7 Marking and instructions
8 Protection against access to live parts
9 Starting of motor-operated appliances
10 Power input and current
11 Heating
12 Void
13 Leakage current and electric strength at operating
temperature
14 Transient overvoltages
15 Moisture resistance
16 Leakage current and electric strength
17 Overload protection of transformers and associated
circuits
18 Endurance
19 Abnormal operation
20 Stability and mechanical hazards
21 Mechanical strength
22 Construction
23 Internal wiring
24 Components
25 Supply connection and external flexible cords
26 Terminals for external conductors
27 Provision for earthing
28 Screws and connections
29 Clearances, creepage distances and solid insulation
30 Resistance to heat and fire
31 Resistance to rusting
32 Radiation, toxicity, and similar hazards
Annexes
Annex A (informative) - Routine tests
Annex B (normative) - Appliances powered by rechargeable
batteries
Annex D (normative) - Thermal motor protectors
Annex DVA (informative) - Component standards cross
reference
Annex AA (normative) - Precast paving slabs
Annex BB (normative) - Requirements for internal
combustion engine powered machines using
liquefied petroleum gas (LPG)
Annex CC (informative) - Emission of acoustical noise
Annex DD (informative) - Emission of vibration
Annex 101.DVA (normative) - Requirements for internal
combustion engine powered machines using
fuels such as, but not limited to,
ethanol-gasoline blends, gasoline,
bio-diesel, and diesel
Annex 101.DVB (normative) - Component standards
Annex 101.DVC (normative) - Tabs used in electrical
quick-connect terminals
Bibliography
Pertains to the safety of powered floor treatment machines intended for commercial indoor or outdoor use for the following applications: - scrubbing, - wet or dry pick-up, - polishing and dry buffing, - application of wax, sealing products and powder based detergents, - shampooing, and - stripping, grinding and scarifying of floors with an artificial surface.
| DevelopmentNote |
Jointly published by CSA and UL. Also numbered as CSA C22.2.60335-2-67. (01/2018)
|
| DocumentType |
Standard
|
| Pages |
0
|
| PublisherName |
Underwriters Laboratories
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| IEC 60216-6:2006 | Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
| UL 60335-2-72:1ED 2017-09-15 | Household and Similar Electrical Appliances - Safety - Part 2-72: Particular Requirements for Floor Treatment Machines With or Without Traction Drive, for Commercial Use |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| C22.2 NO. 243-17 | Vacuum cleaners, blower cleaners, and household floor finishing machines (Binational standard with UL 1017) |
| SAE J 2045 : 2012 | PERFORMANCE REQUIREMENTS FOR FUEL SYSTEM TUBING ASSEMBLIES |
| SAE J 1681 : 2000 | GASOLINE, ALCOHOL, AND DIESEL FUEL SURROGATES FOR MATERIALS TESTING |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| SAE J1128_201512 | LOW VOLTAGE PRIMARY CABLE |
| IEC 60695-10-3:2016 | Fire hazard testing - Part 10-3: Abnormal heat - Mould stress relief distortion test |
| IEC 60335-2-10:2002+AMD1:2008 CSV | Household and similar electrical appliances - Safety - Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines |
| IEC 60335-2-72:2016 | Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for floor treatment machines with or without traction drive, for commercial use |
| IEC 60335-2-69:2016 | Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use |
| IEC 60335-2-2:2009+AMD1:2012+AMD2:2016 CSV | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-2: PARTICULAR REQUIREMENTS FOR VACUUM CLEANERS AND WATER-SUCTION CLEANING APPLIANCES |
| CSA E60335.2.10 : 2006 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-10: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES AND WET SCRUBBING MACHINES |
| CSA E60335.2.69 : 2001 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR WET AND DRY VACUUM CLEANERS, INCLUDING POWER BRUSH, FOR INDUSTRIAL AND COMMERCIAL USE |
| CSA C22.2 No. 10 : 1965 | ELECTRIC FLOOR SURFACING AND CLEANING MACHINES |
| CSA E60335.2.68 : 2001 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR SPRAY EXTRACTION APPLIANCES, FOR INDUSTRIAL AND COMMERCIAL USE |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| SAE J 1127 : 2015 | LOW VOLTAGE BATTERY CABLE |
| SAE J30_201202 | FUEL AND OIL HOSES |
| ISO 3405:2011 | Petroleum products Determination of distillation characteristics at atmospheric pressure |
| ISO 5349-1:2001 | Mechanical vibration Measurement and evaluation of human exposure to hand-transmitted vibration Part 1: General requirements |
| IEC 60312-1:2010+AMD1:2011 CSV | Vacuum cleaners for household use - Part 1: Dry vacuum cleaners - Methods for measuring the performance |
| SAE J 2044 : 2009 | QUICK CONNECT COUPLING SPECIFICATION FOR LIQUID FUEL AND VAPOR/EMISSIONS SYSTEMS |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| IEC 60335-2-68:2012+AMD1:2016 CSV | Household and similar electrical appliances - Safety - Part 2-68:Particular requirements for spray extraction machines, for commercial use |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| SAE J 2260 : 2004 | NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS |
| ISO 6344-2:1998 | Coated abrasives Grain size analysis Part 2: Determination of grain size distribution of macrogrits P12 to P220 |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.