SAE MA 1568 : 2018
Current
The latest, up-to-date edition.
NUT, SELF LOCKING - UNS S66286, 425 DEGREE C AND 650 DEGREE C, 1100 MPA, MJ THREAD, PROCUREMENT SPECIFICATION FOR, METRIC
Hardcopy , PDF
English
30-03-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION OF DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
APPENDIX A - MEASUREMENT OF PERPENDICULARITY
VARIATION OF THE BEARING SURFACE
APPENDIX B - WRENCH TORQUE TEST
APPENDIX C - PUSH OUT TEST
APPENDIX D - TORQUE OUT TEST
APPENDIX E - PERMANENT SET TEST
APPENDIX F - REUSABILITY TEST AT ROOM TEMPERATURE,
AFTER BAKING
APPENDIX G - REUSABILITY TEST AT ROOM TEMPERATURE,
AS RECEIVED CONDITION
APPENDIX H - THREE CYCLES TEST AT ROOM TEMPERATURE
APPENDIX J - ACCEPTANCE CRITERIA OF SURFACE
DISCONTINUITIES ON SELF LOCKING NUTS
Specifies the requirements for the following types of self locking nuts: wrenching nuts, i.e., hex, double hex, spline drive; and anchor nuts, i.e., plate nuts, gang channel nuts, shank (clinch) nuts.
| Committee |
E-25
|
| DocumentType |
Standard
|
| Pages |
41
|
| PublisherName |
SAE International
|
| Status |
Current
|
| Supersedes |
| MIL L 7808 : K (1) | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| SAE AMS 5737 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 2645 : 1995 | FLUORESCENT PENETRANT INSPECTION |
| SAE AMS 5525 : 2012 | STEEL, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND PLATE 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, 1800 DEGREE F (982 DEGREE C) SOLUTION HEAT TREATED |
| SAE MA 1586 : 2013 | WRENCH CONFIGURATION, 12 SPLINE DRIVE, METRIC |
| SAE MA 3374 : 2012 | BOLTS AND SCREWS, UNS S66286, CORROSION AND HEAT RESISTANT STEEL, PROCUREMENT SPECIFICATION, METRIC |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS 5734 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C) SOLUTION HEAT TREATED |
| NA 0012 : REV 2 | FIXTURE, BEARING SURFACE SQUARENESS TEST, SELF-LOCKING NUTS, METRIC |
| SAE AMS 5732 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 2350 : 1989 | STANDARDS AND TEST METHODS |
| SAE MA 1370 : 2012 | SCREW THREADS - MJ PROFILE, METRIC |
| SAE AMS 5731 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED |
| SAE AMS 2411 : 2013 | PLATING, SILVER FOR HIGH TEMPERATURE APPLICATIONS |
| MIL-STD-794 Revision E:1982 | PART AND EQUIPMENT, PROCEDURES FOR PACKAGING AND PACKING OF |
| MA1520A : 2012(R2018) | AREAS FOR CALCULATING STRESS OR LOAD VALUES FOR METRIC MJ EXTERNALLY THREADED FASTENERS |
| MIL-STD-105 Revision E:1989 | SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES |
| SAE AS 1310 : 2012 | FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.