SAE J 311 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FLUID FOR PASSENGER CAR TYPE AUTOMATIC TRANSMISSIONS
22-02-2024
01-01-2000
Gives the procedures and equipment used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It may help those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for use in passenger car and light-duty truck automatic transmissions. The information given will assist the understanding of terms relating to properties, designations and service applications of automatic transmission fluids.
DocumentType |
Standard
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy |
MIL-HDBK-113 Revision C:1989 | GUIDE FOR THE SELECTION OF LUBRICANTS, FUNCTIONAL FLUIDS, PRESERVATIVES AND SPECIALITY PRODUCTS FOR USE IN GROUND EQUIPMENT SYSTEMS |
SAE J 2311 : 2015 | AUTOMATIC TRANSMISSION HYDRAULIC PUMP TEST PROCEDURE |
SAE J 1128 : 2015 | LOW VOLTAGE PRIMARY CABLE |
ISO 8092-2:2005 | Road vehicles — Connections for on-board electrical wiring harnesses — Part 2: Definitions, test methods and general performance requirements |
I.S. EN ISO 8092-2:2006 | ROAD VEHICLES - CONNECTIONS FOR ON-BOARD ELECTRICAL WIRING HARNESSES - PART 2: DEFINITIONS, TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS |
SAE J 2192 : 2016 | RECOMMENDED TESTING METHODS FOR PHYSICAL PROTECTION OF WIRING HARNESSES |
ASTM D 5363 : 2016 : REDLINE | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
ISO 15170-2:2001 | Road vehicles — Four-pole electrical connectors with pins and twist lock — Part 2: Tests and requirements |
SAE J 1678 : 2015 | LOW VOLTAGE ULTRA THIN WALL PRIMARY CABLE |
BS EN ISO 8092-2:2005 | Road vehicles. Connections for on-board electrical wiring harnesses Definitions, test methods and general performance requirements |
EN ISO 8092-2:2005 | Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2005) |
98/711362 DC : DRAFT 98 | ISO/DIS 5092-2 - ROAD VEHICLES - CONNECTIONS FOR ON ON-BOARD ELECTRICAL WIRING HARNESSES - PART 2: DEFINITIONS, TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS |
SAE J 1127 : 2015 | LOW VOLTAGE BATTERY CABLE |
ASTM D 892 : 2013-07 | TEST METHOD FOR FOAMING CHARACTERISTICS OF LUBRICATING OILS |
ASTM D 4951 : 2014 : REDLINE | Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM D 665 : 2014-11 | TEST METHOD FOR RUST-PREVENTING CHARACTERISTICS OF INHIBITED MINERAL OIL IN THE PRESENCE OF WATER |
ASTM D 2882 : 2000 | Standard Test Method for Indicating the Wear Characteristics of Petroleum and Non-Petroleum Hydraulic Fluids in Constant Volume Vane Pump (Withdrawn 2003) |
ASTM D 808 : 2016 : REDLINE | Standard Test Method for Chlorine in New and Used Petroleum Products (High Pressure Decomposition Device Method) |
SAE J 110 : 1997 | SEALS - TESTING OF RADIAL LIP |
ASTM D 1275 : 2015 | Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids |
MS9602 Revision B:1987 | BRACKET ANGLE 90 DEG CRES ARM 5504 .190 X .312 BOLT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.