Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

SAE AS 9138 : 2018

Current

Current

The latest, up-to-date edition.

AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

20-01-2018

$331.47
Including GST where applicable

FOREWORD
INTRODUCTION
1. SCOPE
2. REFERENCES
3. TERMS AND DEFINITIONS
4. GENERAL REQUIREMENTS
5. REQUIRED INFORMATION TO BE DOCUMENTED
6. REQUIREMENTS FOR ACCEPTING PRODUCT BY
    INDIVIDUAL LOTS
7. REQUIREMENTS FOR ACCEPTING PRODUCT PRODUCED
    UNDER SWITCHING RULES
8. REQUIREMENTS FOR ACCEPTING PRODUCT PRODUCED
    UNDER PROCESS CONTROLS
9. ADDITIONAL REQUIREMENTS FOR ACCEPTING PRODUCTS
    BASED ON CONTINUOUS SAMPLING, SKIP-LOT SAMPLING,
    OR METHODS FOR SPECIAL CASES
10. NOTES
APPENDIX A - GUIDELINES FOR ASSIGNING INITIAL RELIABILITY
             REQUIREMENT QUALITY LEVELS
APPENDIX B - ACRONYM LOG
APPENDIX C - MATHEMATICS FOR ACCEPTING PRODUCT UNDER
             LOT-BY-LOT INSPECTION
APPENDIX D - GUIDELINES AND RECOMMENDATIONS FOR SUCCESSFUL
             IMPLEMENTATION OF STATISTICAL PRODUCT ACCEPTANCE METHODS
APPENDIX E - DISCUSSION ON THE TECHNICAL RATIONALE AND HISTORY
             OF THE RELATIONSHIP OF QUALITY PARAMETERS TO RELIABILITY
APPENDIX F - GUIDELINES FOR CHOOSING A STATISTICAL PRODUCT
             ACCEPTANCE TECHNIQUE AND QUALITY PARAMETER
APPENDIX G - GUIDELINES AND RECOMMENDATIONS FOR ACCEPTING
             PRODUCT BY INDIVIDUAL LOTS
APPENDIX H - GUIDELINES FOR SOME SPECIAL ACCEPTANCE METHODS
APPENDIX I - GUIDELINES AND RECOMMENDATIONS FOR ACCEPTING
             PRODUCT PRODUCED UNDER SWITCHING RULES
APPENDIX J - GUIDELINES AND RECOMMENDATIONS FOR ACCEPTING
             PRODUCT PRODUCED UNDER PROCESS CONTROLS
APPENDIX K - GUIDELINES AND RECOMMENDATIONS FOR ACCEPTING
             PRODUCTS BASED ON CONTINUOUS SAMPLING

This standard establishes requirements when implementing statistical product acceptance methods to meet defined risk requirements.

Committee
G-14
DevelopmentNote
Supersedes SAE ARP 9013. (01/2018) Supersedes SAE ARP 9013/1, SAE ARP 9013/2, SAE ARP 9013/3 & SAE ARP 9013/4. (06/2018)
DocumentType
Standard
Pages
94
PublisherName
SAE International
Status
Current

EN 9100:2009 Quality Management Systems - Requirements for Aviation, Space and Defense Organizations
ISO 3951-1:2013 Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
SAE ARP 9013/2 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING ATTRIBUTE OR VARIABLE LOT ACCEPTANCE SAMPLING PLANS
SAE ARP 5580 : 2012 RECOMMENDED FAILURE MODES AND EFFECTS ANALYSIS (FMEA) PRACTICES FOR NON-AUTOMOBILE APPLICATIONS
ISO 2859-3:2005 Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures
MIL-HDBK-1823 Revision A:2009 NONDESTRUCTIVE EVALUATION SYSTEM, RELIABILITY ASSESSMENT
FAA AC 21-43 : 2015 PRODUCTION UNDER 14 CFR PART 21, SUBPARTS F, G, K, AND O
ISO 11462-2:2010 Guidelines for implementation of statistical process control (SPC) — Part 2: Catalogue of tools and techniques
EN 9110:2015 Quality Management Systems - Requirements for Aviation Maintenance Organizations
ISO/IEC Guide 98-1:2009 Uncertainty of measurement — Part 1: Introduction to the expression of uncertainty in measurement
MIL-STD-1235 Revision C:1988 SINGLE AND MULTILEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES FUNCTIONAL CURVES OF THE CONTINUOUS SAMPLING PLANS
ISO/IEC Guide 98-4:2012 Uncertainty of measurement Part 4: Role of measurement uncertainty in conformity assessment
ISO 10576-1:2003 Statistical methods — Guidelines for the evaluation of conformity with specified requirements — Part 1: General principles
SAE AS 9100D : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS
MIL-STD-414 Base Document:1957 SAMPLING PROCEDURE AND TABLE FOR INSPECTION BY VARIABLES FOR PERCENT DEFECTIVE
SAE ARP 4761 : 1996 GUIDELINES AND METHODS FOR CONDUCTION THE SAFETY ASSESSMENT PROCESS ON CIVIL AIRBORNE SYSTEMS AND EQUIPMENT
SAC GB/T 2828-3 : 2008 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 3: SKIP-LOT SAMPLING PROCEDURES
ASQ B1/B2/B3:1996 Guide For Quality Control Charts - Control Chart Method Of Analyzing Data - Control Chart Method Of Controlling Quality During Production
SAE ARP 9013/4 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING CONTINUOUS SAMPLING, SKIP-LOT SAMPLING, OR METHODS FOR SPECIAL CASES
SAE J 1739 : 2009 POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA)
SAE ARP 9013/1 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING ISOLATED LOT SAMPLING METHODS
SAE ARP 9013/3 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING PROCESS CONTROL METHODS
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
SAE AS 9120 : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE DISTRIBUTORS
ISO 11462-1:2001 Guidelines for implementation of statistical process control (SPC) Part 1: Elements of SPC
SAC GB/T 6378-1 : 2008 SAMPLING PROCEDURES FOR INSPECTION BY VARIABLES - PART 1: SPECIFICATION FOR SINGLE SAMPLING PLANS INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION FOR A SINGLE QUALITY CHARACTERISTIC AND A SINGLE AQL
MIL-STD-105 Revision E:1989 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
SAC GB/T 2828-1 : 2012 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION
SAE ARP 9013 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS
SAE AS 9110 : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION MAINTENANCE ORGANIZATIONS
EN 9120:2010 Quality Management Systems - Requirements for Aviation, Space and Defence Distributors
ASQ Z1.9:2003 (R2013) Sampling Procedures And Tables For Inspection By Variables For Percent Nonconforming
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.