SAE AMS 4083 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN, ROUND, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T6), SOLUTION AND PRECIPITATION HEAT TREATED
Hardcopy , PDF
05-01-2019
English
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Specifies an aluminum alloy in the form of seamless round tubing.
| Committee |
AMS-D
|
| DevelopmentNote |
Supersedes SAE AMS 4093 (07/1999) Supersedes SAE AMS T 7081. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| MIL-T-7081 Revision D:1965 | Similar to |
| BS ISO 7169:2014 | Aerospace. Separable tube fittings for fluid systems, for 24° cones, for pressures up to 3 000 psi or 21 000 kPa. Procurement specification, inch/metric |
| SAE AS 6449 : 2017 | SOLID FILM LUBRICANT |
| SAE ARP 994 : 2016 | DESIGN OF TUBING INSTALLATIONS FOR AEROSPACE HYDRAULIC SYSTEMS |
| SAE AS 6116 : 2016 | ALUMINUM FITTINGS, AXIALLY SWAGED TUBE WITH FLARELESS SEPERABLE, FLUID SYSTEM, UP TO 1500 PSI (10340 KPA) MAXIMUM, SPECIFICATION FOR |
| SAE AS 18280 : 2017 | FITTINGS, 24 DEGREES CONE FLARELESS, FLUID CONNECTION, 3000 PSI |
| SAE AS 5958 : 2017 | FITTINGS, AXIALLY SWAGED TUBE WITH FLARELESS SEPARABLE, FLUID SYSTEM FOR OPERATING PRESSURES UP TO AND INCLUDING 5080 PSI (35 000 KPA), SPECIFICATION FOR |
| SAE AS 4459 : 2013 | FITTINGS, TUBE, FLUID SYSTEM 3000 PSIG (21000 KPA) RATED PRESSURE, EXTERNALLY SWAGED, SPECIFICATION FOR |
| SAE AIR 5005 : 2015 | AEROSPACE - COMMERCIAL AIRCRAFT HYDRAULIC SYSTEMS |
| ISO 7169:2014 | Aerospace Separable tube fittings for fluid systems, for 24 degree cones, for pressures up to 3 000 psi or 21 000 kPa Procurement specification, inch/metric |
| SAE ARP 4925 : 2014 | AEROSPACE DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT HELICOPTER HYDRAULIC SYSTEMS |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| SAE AMS 2772 : 2016 | HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS |
| SAE AMS 2355 : 2016 | QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
| ASTM E 215 : 2016 : REDLINE | Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum-Alloy Tube |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.