PREN 1555-5 : DRAFT 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
01-09-2010
12-01-2013
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Fitness for purpose
4.1 Method of preparation of assemblies for testing
4.1.1 General
4.1.2 Butt fusion joints
4.1.3 Electrofusion jointing
4.1.4 Mechanical joints
4.2 Requirements for fitness for purpose
4.2.1 Fitness for purpose for butt fusion joints
4.2.2 Fitness for purpose for electrofusion joints
4.2.3 Fitness for purpose for mechanical joints
5 Overall service (design) coefficient
Annex A (informative) Derating coefficients for operating
temperatures
Annex B (informative) Rapid crack propagation (RCP) resistance
at temperature less than 0 degree C
Bibliography
Defines requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels.
| Committee |
TC 155
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 08/30191156 DC : 0 | Identical |
| 08/30191153 DC : 0 | BS EN 1555-4 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| 02/121566 DC : DRAFT APR 2002 | BS EN 14408-3 - PLASTICS PIPING SYSTEMS FOR THE RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| 08/30191150 DC : 0 | BS EN 1555-3 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| 10/30208795 DC : 0 | BS EN 12007-2 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL RECOMMENDATIONS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| PREN 12007-2 : DRAFT 2010 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL RECOMMENDATIONS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| BS EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
| 08/30191147 DC : 0 | BS EN 1555-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| PREN 1555-4 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| PREN 1555-2 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| EN ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008) |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| PREN 1555-4 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| PREN 1555-3 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| PREN 1555-1 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| EN ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.