PD ISO/TR 16335:2013
Current
The latest, up-to-date edition.
Corrosion of metals and alloys. Corrosion tests in artificial atmospheres. Guidelines for selection of accelerated corrosion test for product qualification
Hardcopy , PDF
English
30-09-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Categories and characteristics of accelerated corrosion
tests
4 Recommended fields of application for different kinds of
tests and their suitability
5 Corrosivity of tests and relative corrosion rates of standard
metals
6 Requirements for test equipment and reproducibility of test
results
7 Recommended procedures for product qualification
Annex A (informative) - Characteristics of standardized
accelerated atmospheric corrosion tests
Annex B (informative) - Initial risk analysis of potential
failure modes for products or functional units
Bibliography
Pertains for the selection of suitable accelerated atmospheric corrosion tests for qualification of products with metallic materials without or with permanent corrosion protection or temporary corrosion protection.
| Committee |
ISENFE/8
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This Technical Report is applicable for the selection of suitable accelerated atmospheric corrosion tests for qualification of products with metallic materials without or with permanent corrosion protection or temporary corrosion protection. The characteristics of a number of standardized accelerated corrosion tests are also given to serve as a guide in the preparation of test specifications.
In this Technical Report the following aspects are taken into account:
Categories of accelerated atmospheric corrosion tests
Recommended fields of application for the different kinds of tests and their suitability
Corrosivity of tests and relative corrosion rates of standard metals
Requirements for test equipment, criteria for reproducibility and correlation with in-service performance
Recommended procedures for product qualification
The main purpose of this Technical Report is to present a framework for comparing the different accelerated corrosion test methods, which presently are available as International Standards. The suitability of a test method varies with the requirements set by the intended application of the product.
| Standards | Relationship |
| ISO/TR 16335:2013 | Identical |
| ISO 16151:2005 | Corrosion of metals and alloys Accelerated cyclic tests with exposure to acidified salt spray, "dry" and "wet" conditions |
| ISO 9223:2012 | Corrosion of metals and alloys — Corrosivity of atmospheres — Classification, determination and estimation |
| ISO 11997-2:2013 | Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light |
| ISO 11130:2010 | Corrosion of metals and alloys Alternate immersion test in salt solution |
| ISO 9226:2012 | Corrosion of metals and alloys — Corrosivity of atmospheres — Determination of corrosion rate of standard specimens for the evaluation of corrosivity |
| IEC 60068-2-60:2015 RLV | Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| ISO 9224:2012 | Corrosion of metals and alloys — Corrosivity of atmospheres — Guiding values for the corrosivity categories |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| ISO 9225:2012 | Corrosion of metals and alloys — Corrosivity of atmospheres — Measurement of environmental parameters affecting corrosivity of atmospheres |
| ISO 14993:2001 | Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions |
| ISO 21207:2015 | Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying |
| ISO 16701:2015 | Corrosion of metals and alloys Corrosion in artificial atmosphere Accelerated corrosion test involving exposure under controlled conditions of humidity cycling and intermittent spraying of a salt solution |
| ISO 11997-1:2017 | Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 1: Wet (salt fog)/dry/humid |
| ISO 10062:2006 | Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es) |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 20340:2009 | Paints and varnishes Performance requirements for protective paint systems for offshore and related structures |
| ISO 11844-1:2006 | Corrosion of metals and alloys Classification of low corrosivity of indoor atmospheres Part 1: Determination and estimation of indoor corrosivity |
| IEC 60068-2-52:2017 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| ISO 11474:1998 | Corrosion of metals and alloys — Corrosion tests in artificial atmosphere — Accelerated outdoor test by intermittent spraying of a salt solution (Scab test) |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.