ONORM EN 12301 : 2009
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
PLASTICS AND RUBBER MACHINES - CALENDERS - SAFETY REQUIREMENTS
15-02-2020
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
4.1 Mechanical hazards
4.2 Electrical hazards
4.3 Thermal hazards
4.4 Hazards due to noise
4.5 Hazards generated by neglecting ergonomic
principles
4.6 Hazards due to failure to energy supply
4.7 Hazards due to failure of the control systems
4.8 Slip, trip and fall hazards
5 Safety requirements and/or measures
5.1 Mechanical hazards
5.2 Electrical hazards
5.3 Thermal hazards
5.4 Hazards due to noise
5.5 Hazards generated by neglecting ergonomic
principles
5.6 Hazards due to failure to energy supply
5.7 Hazards due to failure of the control systems
5.8 Slip, trip and fall hazards
6 Verification of the safety requirements and/or
measures
7 Information for use
7.1 Instruction handbook
7.2 Marking
Annex A (informative) Examples of different types of
calenders
Annex B (informative) Examples of calendering processes
Annex C (informative) Hazards generated by the materials
being processed
Annex D (informative) Calculation of dimension L of the
trapping zone (for rolls of equal
diameters)
Annex E (informative) Fixed guards at the trapping zone
Annex F (informative) Example of a particular type of guard
with limited movement preventing
access to the trapping zone
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or
other provisions of EU directives
Bibliography
Requirements for safety relating to the design and construction of multi-roll calenders intended for the processing of rubber or plastics are defined. The calender alone, including all components fixed to its frame are concerned with this standard. Examples of various types of calenders are shown in Annex A and calendering processes are shown in Annex B. The standard deals with the significant hazards listed in Clause 4. The following machines are excluded: two-roll calender forming an integral unit with an extruder (roller head); two or three-roll polishing, laminating and embossing units (which are not calenders) installed downstream of extruders in film processing lines.
| Committee |
TC 052
|
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| EN 12301:2000+A1:2008 | Identical |
| DIN EN 12301:2015-12 (Draft) | Identical |
| BS EN 12301 : 2000 | Identical |
| UNE-EN 12301:2001 | Identical |
| UNI EN 12301 : 2008 | Identical |
| I.S. EN 12301:2000 | Identical |
| NBN EN 12301 : 2000 + A1 2008 | Identical |
| NEN EN 12301 : 2000 + A1 2008 | Identical |
| NS EN 12301 : 2000 + A1 2008 | Identical |
| SN EN 12301 : 2000 + A1 2008 | Identical |
| NF EN 12301 : 2000 + A1 2008 | Identical |
| DIN EN 12301:2010-02 | Identical |
| ONORM EN ISO 3743-2 : 2009 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| ONORM EN ISO 13857 : 2008 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ONORM EN ISO 11204 : AUG 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 11203:1995 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| ONORM EN ISO 11203 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS FROM THE SOUND POWER LEVEL |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| ONORM EN ISO 11202 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.