NF EN 676 : 2004 + A2 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
29-10-2021
12-01-2013
Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Exigences de construction et de fonctionnement -
Exigences de sécurité et/ou mesures de
protection
5 Méthodes d'essai
6 Marquage, étiquetage, emballage
Annexe A (informative) Détermination des caractéristiques
de combustion monoxyde de carbone et oxydes
d'azote
Annexe B (informative) Exemples de séquence de boîtier de
commande
Annexe C (informative) Gaz d'essais
Annexe D (informative) Raccordements en gaz en usage
dans les différents pays
Annexe E (informative) Essais
Annexe F (informative) Utilisation de lignes gaz alternatives
et de documents de vérification
Annexe G (informative) Correction de l'influence de la
température et de l'humidité de l'air de
combustion sur les émissions de NOx
Annexe H (informative) Vérification du dispositif de controle
d'air
Annexe I (informative) Exigences supplémentaires pour
applications spécifiques U
Annexe J (normative) Risques associés à la machine -
Exigences de sécurité et/ou mesures de protection
Annexe K (normative) Exigences supplémentaires pour
les brûleurs avec parties sous pression et
brûleurs avec dispositifs de surveillance tels
que définis dans la Directive 97/23/CE
Équipements sous pression (PED)
Annexe ZA (informative) Divergences A
Annexe ZB (informative) Articles de la présente Norme
européenne concernant les exigences
essentielles ou d'autres dispositions des
Directives UE
Annexe ZC (informative) Relation entre la présente norme
européenne et les exigences essentielles de
la Directive 97/23/CE Équipements sous
pression (PED)
Annexe ZD (informative) Relation entre la présente norme
européenne et les exigences essentielles de
la Directive Machines 98/37/CE
Annexe ZE (informative) Relation entre la présente norme
européenne et les exigences essentielles de
la Directive Machines 2006/42/CE
Bibliographie
Describes the terminology, the general requirements for the construction and operation of automatic forced draught gas burners and also the provision of control and safety devices, and the type test procedure for these burners.
| DevelopmentNote |
Indice de classement: D35-310PR. Supersedes NFD 35 361, NFD 35 324 and NFD 35 422. (10/2001) Supersedes NFD 35 310. (03/2004) 2004 Edition Re-issued in August 2008 & incorporates AMD 2 2008. (08/2008) PR NF EN 676 May 2012. (06/2012) PR NF EN 676 February 2017. (03/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 676 : 2008 | Identical |
| BS EN 676 : 2003 | Identical |
| NEN EN 676 : 2003 + A2/C1 2008 | Identical |
| NS EN 676 : 2008 AC 2008 | Identical |
| ONORM EN 676 : 2008 | Identical |
| NBN EN 676 : 2003 COR 2008 | Identical |
| UNE-EN 676:2004 | Identical |
| I.S. EN 676:2003 | Identical |
| DIN EN 676:2012-03 (Draft) | Identical |
| DIN EN 676:2008-11 | Identical |
| NF EN 15456 : 2008 | HEATING BOILERS - ELECTRICAL POWER CONSUMPTION FOR HEAT GENERATORS - SYSTEM BOUNDARIES - MEASUREMENTS |
| NF EN ISO 9606-2 : 2005 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 2: ALUMINIUM AND ALUMINIUM ALLOYS |
| NF EN ISO 228-1 : 2003 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| NF EN ISO 9606-4 : 1999 | APPROVAL TESTING OF WELDERS - FUSION WELDING - PART 4: NICKEL AND NICKEL ALLOYS |
| NF EN ISO 12100-1 : 2004 AMD 1 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| NF EN 12067-2 : 2004 | GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND FOR GAS BURNING APPLIANCES - PART 2: ELECTRONIC TYPES |
| NF EN 10217-1 : 2002 AMD 1 2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 1: NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES |
| NF EN 88-1 : 2011 + A1 2016 | PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA |
| NF EN 12067-1 : 98 AMD 1 2003 | GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES |
| NF EN ISO 15614-7 : 2016 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 7: OVERLAY WELDING |
| NF EN ISO 9606-5 : 2000 | APPROVAL TESTING OF WELDERS - FUSION WELDING - PART 5: TITANIUM AND TITANIUM ALLOYS, ZIRCONIUM AND ZIRCONIUM ALLOYS |
| NF EN 10216-1 : 2014 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 1: NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES |
| NF EN ISO 9606-3 : 1999 | APPROVAL TESTING OF WELDERS - FUSION WELDING - PART 3: COPPER AND COPPER ALLOYS |
| NF EN 10208-2 : 2009 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 2: PIPES OF REQUIREMENT CLASS B |
| NF EN 334 : 2005 + A1 2009 | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| NF EN 15036-1 : 2007 | HEATING BOILERS - TEST REGULATIONS FOR AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS - PART 1: AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS |
| NF EN 10220 : 2003 | SEAMLESS AND WELDED STEEL TUBES - GENERAL TABLES OF DIMENSIONS AND MASSES PER UNIT LENGTH |
| NF EN ISO 15614-11 : 2002 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 11: ELECTRON AND LASER BEAM WELDING |
| NF EN 50156-1 : 2015 | ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION |
| NF EN 88-2 : 2008 | PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR |
| NF EN 60529 : 92 AMD 2 2014 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| NF EN ISO 15609-4 : 2009 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 4: LASER BEAM WELDING |
| NF EN 1092-2 : 1997 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 2: CAST IRON FLANGES |
| NF EN ISO 15609-1 : 2005 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 1: ARC WELDING |
| NF EN 10204 : 2005 | METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS |
| NF EN 1088 : 1996 + A2 2008 | SAFETY OF MACHINERY - INTERLOCKING DEVICES ASSOCIATED WITH GUARDS - PRINCIPLES FOR DESIGN AND SELECTION |
| NF EN 61310-1 : 2008 | SAFETY OF MACHINERY - INDICATION, MARKING AND ACTUATION - PART 1: REQUIREMENTS FOR VISUAL, ACOUSTIC AND TACTILE SIGNALS |
| NF EN 1854 : 2010 | PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| NF EN ISO 4871 : 2009 | ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT |
| NF EN ISO 3166-1 : 2014 | CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES AND THEIR SUBDIVISION - PART 1: COUNTRY CODES |
| NF EN 294 : 1992 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| NF EN 10208-1 : 2009 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| NF EN 1643 : 2014 | SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES |
| NF EN 10226-1 : 2004 | PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION |
| NF EN ISO 13849-1 : 2016 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| NF EN 161 : 2011 + A3 2013 | AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES |
| NF EN 298 : 2012 | AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| NF EN ISO 15609-3 : 2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURES SPECIFICATION - PART 3: ELECTRON BEAM WELDING |
| NF EN 1092-1 : 2007 + A1 2013 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES |
| NF EN ISO 15612 : 2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BY ADOPTION OF A STANDARD WELDING PROCEDURE |
| NF EN ISO 15609-5 : 2011 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 5: RESISTANCE WELDING |
| NF EN ISO 12100-2 : 2004 AMD 1 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| NF EN ISO 15609-2 : 2001 AMD 1 2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 2: GAS WELDING |
| NF EN 1092-3 : 2004 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| NF EN 953 : 1997 + A1 2009 | SAFETY OF MACHINERY - GUARDS - GENERAL REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF FIXED AND MOVABLE GUARDS |
| 1990/396/EEC : 1990 | COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.