Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

NF EN 1175-1 : 1998 + A1 2011

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL REQUIREMENTS - PART 1: GENERAL REQUIREMENTS FOR BATTERY POWERED TRUCKS

Superseded date

30-09-2021

Superseded by

NF EN 1175:2020

Published date

12-01-2013

Sorry this product is not available in your region.

Foreword
0 Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 General requirements
    5.1 Traction battery
          5.1.1 Installation and protection
          5.1.2 Constraining
          5.1.3 Disconnection
    5.2 Battery connections
    5.3 Heat dissipating electrical components
    5.4 Electric motors
    5.5 Contactors
    5.6 Electro-mechanical brakes
    5.7 Protection against electric shock
          5.7.1 Direct contact
          5.7.2 Indirect contact
          5.7.3 Connection to the frame
          5.7.4 On-board chargers
    5.8 Protection of electrical equipment
          5.8.1 Short circuits and overloads
          5.8.2 Overcurrent protective devices
    5.9 Safety related control systems
          5.9.1 Low voltage
          5.9.2 Frame faults
          5.9.3 Travel control system
          5.9.4 Pulse control travel systems
          5.9.5 Prevention of travel
          5.9.6 Steering control
          5.9.7 Load handling control
          5.9.8 Tiller control
          5.9.9 Speed limitation
          5.9.10 Slack wire-ropes or chains
    5.10 Conductors
          5.10.1 Protections
          5.10.2 Cross-sectional area
          5.10.3 Specification
    5.11 Wiring practices
          5.11.1 Multicore cables
          5.11.2 Main current cables
          5.11.3 Wiring that flexes
          5.11.4 Mechanical protection
          5.11.5 Identification
    5.12 Battery charging
          5.12.1 Movement during charging
          5.12.2 Charger switching
    5.13 Emergency switching off
          5.13.1 Access
          5.13.2 Function
    5.14 Dielectric test (type test)
          5.14.1 Performance
          5.14.2 Test voltage
          5.14.3 Electronic components
    5.15 Insulation resistance test (routine test)
          5.15.1 Test voltage
          5.15.2 Insulation resistance of truck
          5.15.3 Insulation resistance of battery
6 Additional requirements for nominal voltages in excess of
    120 V
    6.1 Battery
          6.1.1 Container
          6.1.2 Terminals and connectors
          6.1.3 Poles
          6.1.4 Cover
    6.2 Battery connectors
          6.2.1 Requirements
          6.2.2 Emergency disconnection
    6.3 Protection against electric shock
          6.3.1 Electrical enclosures
          6.3.2 Circuits
          6.3.3 Bonding
          6.3.4 Detection of frame faults
    6.4 Emergency switching off
    6.5 Insulation resistance test (routine test)
          6.5.1 Test voltage
          6.5.2 Insulation resistance test (routine test)
          6.5.3 Insulation resistance of battery
7 Information for use
    7.1 Electrical diagram
    7.2 Safety checks
    7.3 Battery
    7.4 Minimum marking
Annex A (normative) Connectors for traction batteries
    A.1 Normative references
    A.2 Definitions
          A.2.1 Nominal current
          A.2.2 Emergency breaking current
    A.3 Requirements
          A.3.1 Mounting bracket
          A.3.2 Physical properties
          A.3.3 Contacts
          A.3.4 Rated current
          A.3.5 Polarity reversing
          A.3.6 Contacts with connector casing
          A.3.7 Temperature resistance
          A.3.8 Enclosure protection
          A.3.9 Protection of half-connector fitted to the
                  battery
          A.3.10 Coding
          A.3.11 Cable sections
          A.3.12 Locking of half-connectors
    A.4 Type-test methods
          A.4.1 Coding test
          A.4.2 Samples
          A.4.3 Preconditioning
          A.4.4 Temperature rise test
          A.4.5 Low temperature test
          A.4.6 Mechanical life test
          A.4.7 Sequential treatment for drop test
          A.4.8 Drop test
          A.4.9 Dielectric test
          A.4.10 Test of disconnection in overload conditions
                  for range 1 only
    A.5 Maintenance of quality
    A.6 Information for use
Annex B (normative) Electric motors - Output and test rules
    B.1 Normative references
    B.2 Definitions
    B.3 Classification of enclosure and cooling
          B.3.1 Protection
          B.3.2 Cooling
    B.4 Requirements
          B.4.1 Rated output
          B.4.2 Classes of insulation
          B.4.3 Rated output test
          B.4.4 Characteristic curves
          B.4.5 Tolerances on characteristic curves
          B.4.6 Overspeed test
          B.4.7 Dielectric test
          B.4.8 Terminal markings
          B.4.9 Markings - Identification
    B.5 Testing
          B.5.1 General
          B.5.2 Type tests
          B.5.3 Routine tests
Annex C (normative) Electromagnetic contactors
    C.1 Definitions
    C.2 Nominal service conditions
          C.2.1 Climatic conditions
    C.3 Types of contactor
          C.3.1 Type A
          C.3.2 Type B
          C.3.3 Type C
          C.3.4 Type D
    C.4 General requirements
          C.4.1 Limits of operation
          C.4.2 Mechanical durability
    C.5 Type tests
          C.5.1 Temperature rise test of main test circuit
          C.5.2 Temperature rise tests of operating coils
          C.5.3 Dielectric tests
          C.5.4 Verification of operating limits
          C.5.5 Verification of rated making and breaking
                  capacities in proving operation
          C.5.6 Verification of rated making and breaking
                  capacities of intermittently rated
                  contactors of Table C.6 category 2
          C.5.7 Verification of mechanical durability
    C.6 Routine test
          C.6.1 Operating limits
          C.6.2 Dielectric test
    C.7 Marking
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or other provisions of EU
Directives

Defines electrical and related mechanical safety requirements for design and construction of the electrical installation in battery powered industrial trucks, having nominal voltages of the truck system not exceeding 240 V. Describes possible hazards which could happen during the normal use of the truck, under specified climatic conditions.

DevelopmentNote
Indice de classement: H96-330-1. 1998 Edition Re-Issued in February 2011 & incorporates AMD 1 2011. (02/2011)
DocumentType
Standard
PublisherName
Association Francaise de Normalisation
Status
Superseded
SupersededBy

NF EN 15000 : 2008 SAFETY OF INDUSTRIAL TRUCKS - SELF PROPELLED VARIABLE REACH TRUCKS - SPECIFICATION, PERFORMANCE AND TEST REQUIREMENTS FOR LONGITUDINAL LOAD MOMENT INDICATORS AND LONGITUDINAL LOAD MOMENT LIMITERS

IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
HD 405.1 : S1 AMD 1 TESTS ON ELECTRIC CABLES UNDER FIRE CONDITIONS - TEST ON A SINGLE VERTICAL INSULATED WIRE OR CABLE
EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN 12895:2015 Industrial trucks - Electromagnetic compatibility
EN 563:1994/A1:1999/AC:2000 SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
EN 60947-3:2009/A2:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015)
HD 53.8 : 200S5 ROTATING ELECTRICAL MACHINES - TERMINAL MARKINGS AND DIRECTION OF ROTATION OF ROTATING MACHINES
ISO 5053:1987 Powered industrial trucks Terminology
HD 53-6 : 200S1 ROTATING ELECTRICAL MACHINES - METHODS OF COOLING ROTATING MACHINERY
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 6743-4:2015 Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more