NASM 1312-8 : 2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FASTENER TEST METHODS, METHOD 8, TENSILE STRENGTH
Hardcopy
29-04-2023
English
01-01-2001
1 SCOPE
1.1 Applicability
2 REFERENCED DOCUMENTS
2.1 Government documents
2.2 Other publications
3 DEFINITIONS
4 GENERAL REQUIREMENTS
4.1 Test apparatus
4.2 Test specimens
5 DETAIL REQUIREMENTS
5.1 Test procedures
5.2 Loading rate
5.3 Load-deflection curves
5.4 Failing load determination
5.5 Yield load determination
5.6 Number of specimens
6 NOTES
6.1 Test report
FIGURES
Figure
1. Tension fixtures for short grip fasteners
2. Tension setup
3. Test plate
4. Tension fixture assembly
5. Sample load-deflection curve
6. Johnson's two-thirds approximate method for
determination of yield strength
TABLES
Table
I. Tension load rates
Defines procedure for testing all types of structural fasteners in axial tension at room temperature.
| Committee |
FSC 53GP
|
| DevelopmentNote |
Supersedes MIL STD 1312/8 (A). (05/2001)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
Aerospace Industries Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AS 7460 : 2017 | BOLTS AND SCREWS, TITANIUM ALLOY, 6.0AL-4.0V, PROCUREMENT SPECIFICATION FOR |
| SAE AS 5377 : 2000 | NUT, SELF-LOCKING, 0.7500 THRU 1.5000 THREAD SIZES, UNS S66286, 160,000 PSI, 800 DEGREE F, UNJ THREAD - PROCUREMENT SPECIFICATION |
| SAE AS 4877 : 2017 | BOLTS AND SCREWS, NICKEL ALLOY UNS N07718, CLASSIFICATION: 185 KSI/1200 DEGREES F, PROCUREMENT SPECIFICATION |
| SAE AS 7452 : 2014 | BOLTS AND SCREWS, STEEL, LOW ALLOY HEAT TREATED, ROLL THREADED |
| SAE AS 7474 : 2018 | BOLTS AND SCREWS, STEEL, CORROSION RESISTANT, UNS S17400 TENSILE STRENGTH 140 KSI PROCUREMENT SPECIFICATION |
| SAE AS 7473 : 2018 | BOLTS AND SCREWS, ROLL THREADED PROCUREMENT SPECIFICATION FOR |
| SAE AS 7471 : 2018 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07001 TENSILE STRENGTH 165 KSI, CORROSION AND HEAT RESISTANT, PROCUREMENT SPECIFICATION |
| MIL-DTL-32258 Base Document:2007 | NUT, SELF-LOCKING (RING TYPE NON-METALLIC INSERT), HEAVY HEX, CONTROLLED ROOT RADIUS, NICKEL-COPPER ALLOY |
| DOT/FAA/AR-MMPDS-01 : 20030131 | METALLIC MATERIALS PROPERTIES DEVELOPMENT AND STANDARDIZATION (MMPDS) |
| SAE AS 4891 : 1999 | STUD, LOCKED IN, KEY LOCKED, UNS S66286, CLASSIFICATION: 140 KSI PROCUREMENT SPECIFICATION FOR |
| SAE AS 7479 : 2013 | BOLTS AND SCREWS, STEEL, UNS S66286, 1650 DEGREES F SOLUTION HEAT TREATED, PRECIPITATION HEAT TREATED BEFORE ROLL THREADED |
| SAE AS 5270 : 2013 | BOLTS, SCREWS AND STUDS, NICKEL ALLOY, UNS N07718, WORK-STRENGTHENED, TENSILE STRENGTH 220 KSI, PROCUREMENT SPECIFICATION |
| SAE AS 45909 : 2015 | STUD, LOCKED IN, RING LOCKED, SERRATED, GENERAL SPECIFICATION FOR |
| SAE AS 7454 : 2016 | BOLTS AND SCREWS, STEEL, LOW ALLOY, HEAT RESISTANT 135000 PSI TENSILE STRENGTH, NORMALIZED AND TEMPERED, ROLL THREADED |
| SAE MA 3375 : 2011 | STUDS, CORROSION AND HEAT RESISTANT STEEL, UNS S66286 TENSILE STRENGTH 900 MPA, PROCUREMENT SPECIFICATION, METRIC, FSC 5307 |
| NASA STD 6008 : 2008 CHANGE 1 2013 | NASA FASTENER PROCUREMENT, RECEIVING INSPECTION, AND STORAGE PRACTICES FOR SPACEFLIGHT HARDWARE |
| NASA STD 6008(INT) : 2006 | NASA FASTENER MANAGEMENT AND CONTROL PRACTICES |
| SAE AS 7455 : 2016 | BOLTS AND SCREWS, STEEL, LOW ALLOY, HEAT RESISTANT HARDENED AND TEMPERED, ROLL THREADED |
| SAE AS 7470 : 2012 | BOLTS AND SCREWS, STEEL, CORROSION AND MODERATE HEAT RESISTANT HEAT TREATED, ROLL THREADED |
| SAE AS 7456 : 2016 | STUDS, STEEL, LOW ALLOY, HEAT TREATED, ROLL THREADED |
| SAE AS 7466 : 2014 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, FATIGUE RATED, PROCUREMENT SPECIFICATION |
| SAE AS 7468 : 2012 | BOLTS, COBALT-CHROMIUM-NICKEL ALLOY, UNS R30035, TENSILE STRENGTH 260 KSI, PROCUREMENT SPECIFICATION |
| SAE AS 7459 : 2015 | BOLTS AND SCREWS, STEEL UNS K14675 TENSILE STRENGTH 195 KSI FATIGUE AND STRESS-RUPTURE RATED PROCUREMENT SPECIFICATION |
| SAE AS 7475 : 2015 | BOLTS, COBALT-CHROMIUM-NICKEL ALLOY, UNS R30159, TENSILE STRENGTH 260 KSI, PROCUREMENT SPECIFICATION |
| SAE AS 7458 : 2016 | STUDS, STEEL, LOW ALLOY, HEAT RESISTANT NORMALIZED AND TEMPERED, ROLL THREADED 135000 PSI TENSILE STRENGTH |
| SAE AS 7461 : 2015 | BOLTS AND SCREWS, TITANIUM ALLOY, 6AL-4V, UNS R56400, FATIGUE-RATED, PROCUREMENT SPECIFICATION FOR |
| SAE AS 7467 : 2013 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, STRESS RUPTURE RATED, PROCUREMENT SPECIFICATION |
| SAE AS 7482 : 2015 | STUDS, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, TENSILE STRENGTH 130 KSI, 1800 DEGREES F SOLUTION HEAT TREATED, AGED BEFORE ROLL THREADING PROCUREMENT SPECIFICATION |
| EN 4176:2005 | Aerospace series - Lockbolts, 100° countersunk normal head or protruding head, tension- / sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating - Collars in titanium TI-P99002 or aluminium alloy 2024 - Metric series - Technical specification |
| SAE AS 4393 : 2015 | NUT, SELF-LOCKING, UNS S66286, 1200 DEGREES F, 160,000 PSI, UNJ THREAD |
| SAE AS 7477 : 2017 | BOLTS AND SCREWS, STEEL, UNS S66286 TENSILE STRENGTH 130 KSI, PROCUREMENT SPECIFICATION |
| BS EN 4176:2005 | Aerospace series. Lockbolts, 100° countersunk normal head or protruding head, tension-/ sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating. Collars in titanium TI-P99002 or aluminium alloy 2024. Metric series. Technical specification |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 10012-2:1997 | Quality assurance for measuring equipment Part 2: Guidelines for control of measurement processes |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ANSI/NCSL Z540 2 : 1997(R2012) | U.S. GUIDE TO EXPRESSION OF UNCERTAINTY IN MEASUREMENT |
| ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.