MIL-STD-649 Revision C:1976
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Aluminum and Magnesium Products Preparation for Shipment and Storage(S/S by ASTM-B660)
Available format(s)
PDF
Published date
07-06-1976
Publisher
Superseded date
23-07-2013
Superseded by
$34.82
Including GST where applicable
Covers minimum requirements for materials, containers, methods and procedures for the preparation of aluminum and magnesium products for shipment and storage.
| DocumentType |
Standard
|
| Pages |
58
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
| DOD-S-87956 Base Document:1979 | SHELTER, S-80A AND S-82A (NO S/S DOCUMENT) |
| MIL M 46039 : A | MAGNESIUM ALLOY BAR, ROD AND SPECIAL SHAPED SECTIONS, EXTRUDED (ZK21A) |
| SAE AMS4222H | Aluminum Alloy Castings, Sand, Moderate Heat Resistance 4.0Cu - 2.0Ni - 1.5Mg - 0.12Ti (242.0P) Solution Heat Treated and Stabilized |
| QQ-A-200 Revision E:1980 | Aluminum Alloy, Bar, Rod, Shapes, Structural Shapes, Tube and Wire, Extruded; General Specification for (Refer to ASTM-B241/B241M, ASTM-B221, ASTM-B308/B308M and SAE-AMS-QQ-A-200) |
| MIL-A-22771 Revision D:1984 | Aluminum Alloy Forgings, Heat Treated (S/S by SAE-AMS-A-22771) |
| QQ-A-1876 Base Document:1974 | ALUMINUM FOIL |
| SAE AMSWWT700B | Tube, Aluminum and Aluminum Alloy, Drawn, Seamless, General Specification for |
| SAE AMS4012G | Aluminum Sheet, Laminated Edge Bonded |
| MIL-A-21180 Revision D:1984 | Aluminum-Alloy Castings, High Strength (S/S by SAE-AMS-A-21180) |
| SAE AMS4000F | Aluminum Sheet and Plate (1060-0) |
| MIL-W-22248 Revision A:1971 | Weldments, Aluminum and Aluminum Alloy |
| MIL-STD-726 Revision H:1985 | PACKAGING REQUIREMENTS CODES (S/S BY MIL-STD-2073-2) |
| MIL-A-12545 Revision D:1989 | Aluminum Alloy Impacts (S/S BY ASTM-B221) |
| QQ-A-371 Revision F:1971 | ALUMINUM ALLOY INGOT (FOR REMELTING) (S/S BY ASTM-B179) |
| QQ-A-596 Revision E:1981 | Aluminum Alloy Permanent and Semipermanent Mold Castings (S/S by ASTM-B108) |
| MIL M 8917 : A NOTICE 2 | MAGNESIUM ALLOY SHEET AND PLATE [HM 21A - TB] [ASG] |
| MIL A 46158 : 0 | ALUMINUM ALLOY STRIP, STAINLESS STEEL CLAD |
| MIL-A-46104 Base Document:1965 | Aluminum Alloy Bar, Rod, Shapes, and Tube, Extruded, 6070 (S/S by ASTM-B221 and ASTM-B221M) |
| MIL-M-45202 Revision C:1981 | Magnesium Alloy, Anodic Treatment of (S/S by ASTM-D1732) |
| MIL-HDBK-772 Base Document:1981 | Military Packaging Engineering (No S/S Document) |
| MIL-T-7081 Revision D:1965 | TUBE, ALUMINUM ALLOY, SEAMLESS, ROUND, DRAWN 6061, AIRCRAFT HYDRAULIC QUAL ITY (S/S BY SAE-AMS-T-7081) |
| MIL-M-26075 Revision D:1969 | Magnesium-Alloy Sheet and Plate (HK31A) (See Notice 1 for Replacement Information) |
| MIL-M-46143 Base Document:1988 | MAGNESIUM LITHIUM ALLOY CASTINGS (LS141A AND LZ145A) (NO S/S DOCUMENT) |
| QQ-M-38 Revision B:1969 | MAGNESIUM ALLOY DIE CASTINGS (AZ91A) (S/S BY ASTM-B94) |
| MIL A 52242 : A | ALUMINUM ALLOY EXTRUDED ROD, BAR, AND SHAPES, 7001 |
| SAE AMS 4440 : 1999 | MAGNESIUM ALLOY CASTINGS, SAND 3.5CE - 0.70ZR (EK41A-T5) PRECIPITATION HEAT TREATED |
| SAE AMS4051G | Aluminum Alloy, Sheet and Plate, Alclad, 6.8Zn - 2.8Mg - 2.0Cu - 0.23Cr (Alclad 7178-O), Annealed |
| MIL P 25995 : B | PIPE, ALUMINUM ALLOY, DRAWN OR EXTRUDED |
| SAE AMS4023F | Aluminum Alloy Sheet and Plate, Alclad 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061; -T6 Sheet, -T651 Plate) |
| ASTM B 90M : 1990 | Specification for Magnesium-Alloy Sheet and Plate (Metric) (Withdrawn 1993) |
| SAE AMS4231G | Castings, Sand, 4.5Cu - 1.1Si, Solution and Precipitation Heat Treated |
| SAE AMS4240G | Castings, Sand, 10Mg, Solution Heat Treated and Naturally Aged |
| MIL-Z-63472 Base Document:1980 | ZINC-ALUMINUM SUPERPLASTIC ALLOYS FOR THERMO FORMING, DEEP DRAWING AND STRETCH FORMING (NO S/S DOCUMENT) |
| SAE AMSM45202B | Magnesium Alloys, Anodic Treatment of |
| MIL-A-63547 Base Document:1982 | Aluminum Alloy 7475, Rod (No S/S Document) |
| MIL A 11267 : C | ALUMINUM ALLOY SHEET, 8280 |
| QQ-B-655 Revision C:1987 | BRAZING ALLOYS, ALUMINUM AND MAGNESIUM, FILLER METAL (S/S BY AWS-A5.8) |
| MIL F 46048 : A | FLOOR PLATE, RAISED PATTERN, MAGNESIUM ALLOY, (AZ31B) ROLLED |
| MIL A 81596 : A | ALUMINUM FOIL FOR SANDWICH CONSTRUCTION |
| MIL-M-46062 Revision C:1985 | MAGNESIUM ALLOY CASTINGS, HIGH STRENGTH (NO S/S DOCUMENT) |
| MIL-A-52174 Revision B:1972 | Aluminum Alloy Duct Sheet (S/S by ASTM-B209, ASTM-B209M, ANSI-H35.2, and ANSI-H35.2M) |
| MIL-B-20148 Revision D:1987 | Brazing Sheet, Aluminum Alloy (S/S by SAE-AMS-B-20148) |
| SAE AMS4275E | Castings, Permanent Mold 6.2Sn - 1Cu - 1Ni Stress Relieved |
| PPP-T-76 Revision C:1976 | Tape, Packaging, Paper (for Carton Sealing) (S/S by ASTM-D5486) |
| MIL C 16173 : E | CORROSION PREVENTIVE COMPOUND, SOLVENT CUTBACK, COLD APPLICATION |
| PPP-C-96 Revision E:1992 | Cans, Metal, 28 Gage and Lighter |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| PPP-B-636 Revision J:1981 | Boxes, Shipping, Fiberboard (S/S by ASTM-D1974 and ASTM-D5118) |
| MIL P 17667 : D | PAPER, WRAPPING, CHEMICALLY NEUTRAL (NON CORROSIVE) |
| MIL-STD-147 Revision E:2008 | PALLETIZED UNIT LOADS |
| MIL-M-3171 Revision C:1966 | Magnesium Alloy, Processes for Pretreatment and Prevention of Corrosion on (S/S by SAE-AMS-M-3171) |
| PPP-S-760 Revision B:1973 | STRAPPING, NONMETALLIC (AND CONNECTORS) (S/S BY ASTM-D3950-87) |
| PPP-B-566 Revision E:1974 | Boxes, Folding, Paperboard |
| PPP-F-320 Revision D:1970 | Fiberboard: Corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes (S/S by ASTM-D4727) |
| LLL-B-810 Revision B:1973 | Building Board, (Hardboard) Hard Pressed, Vegetable (S/S by ANSI-A135.4) |
| QQ-S-781 Revision H:1974 | STRAPPING, STEEL, AND SEALS (S/S BY ASTM-D3953-87) |
| PPP-D-705 Revision E:1994 | Drum, Shipping and Storage: Steel, 16 and 30 Gallon Capacity (Future acquisitions for this material should refer to MIL-DTL-6054) |
| PPP-T-495 Revision B:1974 | Tubes, Mailing, and Filing |
| MIL B 121 : F | BARRIER MATERIAL, GREASEPROOFED, WATERPROOFED, FLEXIBLE |
| PPP-T-60 Revision E:1986 | Tape: Packaging, Waterproof (S/S by ASTM D5486/ASTM-D5486M) |
| MIL L 7870 : B | LUBRICATING OIL, GENERAL PURPOSE, LOW TEMPERATURE |
| MMM-A-125 Revision D:1984 | ADHESIVE, CASEIN-TYPE, WATER AND MOLD RESISTANT (S/S BY ASTM-B4689-90) |
| MIL B 131 : H | BARRIER MATERIAL, WATER VAPOR PROOF, GREASEPROOF, FLEXIBLE HEAT SEALABLE |
| PPP-D-729 Revision E:1977 | Drums, Shipping and Storage, Steel, 55-Gallon (208 Liters) |
| FED-STD-101 Revision C:1980 | TEST PROCEDURES FOR PACKAGING MATERIALS (CHANGE NOTICES 1 THRU 3 ARE INCORPORATED IN WITH REVISION C) (S/S BY MIL-STD-3010) |
| FF-N-105 Revision B:1971 | Nails, Brads, Staples and Spikes: Wire, Cut and Wrought (No S/S Document) |
| PPP-P-704 Revision E:1981 | Pails, Metal: (Shipping, Steel, 1 through 12 Gallons) |
| MIL-C-11796 Revision C:1986 | Corrosion Preventive Compound, Petrolatum, Hot Application |
| PPP-T-45 Revision D:1977 | Tape, Gummed, Paper, Reinforced and Plain, for Sealing and Securing (S/S by A-A-1492 and A-A-1671) |
| NN-P-530 Revision E:1977 | Plywood, Flat Panel (S/S by A-A-55057) |
| VV-L-800 Revision C:1983 | Lubricating Oil, General Purpose, Preservative, (Water-Displacing, Low Temperature) (S/S by MIL-PRF-32033) |
| PPP-B-640 Revision D:1966 | Boxes, Fiberboard, Corrugated, Triple Wall (S/S by ASTM-D5168) |
| UU-P-553 Revision C:1976 | PAPER, WRAPPING, TISSUE (S/S BY A-A-1249) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.Are you sure?
Logging out.