ISO 19069-2:2016
Current
The latest, up-to-date edition.
Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
French, English
11-02-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 19069-2:2016 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polypropylene (PP) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are also given. Properties and test methods which are suitable and necessary to characterize PP moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350‑1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 19069, as are the designatory properties specified in ISO 19069‑1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
| DevelopmentNote |
Supersedes ISO/DIS 19069-2 & ISO 1873-2. (02/2016)
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN ISO 19069-2 : 2017 | Identical |
| NBN EN ISO 19069-2 : 2016 | Identical |
| NEN EN ISO 19069-2 : 2016 | Identical |
| NS EN ISO 19069-2 : 2016 | Identical |
| I.S. EN ISO 19069-2:2016 | Identical |
| PN EN ISO 19069-2 : 2016 | Identical |
| SN EN ISO 19069-2 : 2016 | Identical |
| UNI EN ISO 19069-2 : 2016 | Identical |
| UNE-EN ISO 19069-2:2016 | Identical |
| BS EN ISO 19069-2:2016 | Identical |
| EN ISO 19069-2:2016 | Identical |
| DIN EN ISO 19069-2:2016-07 | Identical |
| DIN EN ISO 19069-2:2020-01 | Identical |
| 17/30350548 DC : 0 | BS EN ISO 11357-6 - PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 6: DETERMINATION OF OXIDATION INDUCTION TIME (ISOTHERMAL OIT) AND OXIDATION INDUCTION TEMPERATURE (DYNAMIC OIT) |
| I.S. EN ISO 11357-6:2013 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 6: DETERMINATION OF OXIDATION INDUCTION TIME (ISOTHERMAL OIT) AND OXIDATION INDUCTION TEMPERATURE (DYNAMIC OIT) (ISO 11357-6:2018) |
| EN ISO 11357-6:2018 | Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6:2018) |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 16152:2005 | Plastics Determination of xylene-soluble matter in polypropylene |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 1628-3:2010 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 3: Polyethylenes and polypropylenes |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| ISO 294-4:2001 | Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 62:2008 | Plastics Determination of water absorption |
| ASTM D 5420 : 2016 : REDLINE | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 178:2010 | Plastics Determination of flexural properties |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.