ISO 14956:2002
Current
Current
The latest, up-to-date edition.
Air quality — Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
Available format(s)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English, French
Published date
22-08-2002
$248.75
Including GST where applicable
This International Standard specifies, for the field of air quality measurement procedures, the:
estimation of measurement uncertainty from actual or claimed values of all important performance characteristics of a method under stationary conditions; assessment of whether or not specified values for these performance characteristics comply with the required quality of a measured value at a stated measurand value; evaluation of the applicability of the measurement method based on laboratory performance and confirmatory field test; establishment of requirements on dynamic behaviour of instruments.This International Standard is applicable to measurement procedures whose output is a defined time average.
| Committee |
ISO/TC 146/SC 4
|
| DevelopmentNote |
Supersedes ISO/FDIS 14956 (08/2002)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Standards | Relationship |
| GOST R ISO 14956 : 2007 | Identical |
| NF EN ISO 14956 : 2002 | Identical |
| NEN EN ISO 14956 : 2002 | Identical |
| I.S. EN ISO 14956:2002 | Identical |
| PN EN ISO 14956 : 2006 | Identical |
| SS-EN ISO 14956 : 2002 | Identical |
| BS EN ISO 14956:2002 | Identical |
| EN ISO 14956:2002 | Identical |
| DIN EN ISO 14956:2003-01 | Identical |
| UNE-EN ISO 14956:2003 | Identical |
| PREN 14181 : DRAFT 2012 | STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS |
| PD CEN/TR 15983:2010 | Stationary source emissions. Guidance on the application of EN 14181:2004 |
| PD CEN/TS 1948-5:2015 | Stationary source emissions. Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs Long-term sampling of PCDDs/PCDFs and PCBs |
| 11/30204376 DC : 0 | BS ISO 13271 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF PM10/PM2,5 MASS CONCENTRATION IN FLUE GAS - MEASUREMENT AT HIGHER CONCENTRATIONS BY USE OF VIRTUAL IMPACTORS |
| 07/30142572 DC : 0 | BS EN ISO 23210 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF PM 10/PM 2.5 MASS CONCENTRATION IN FLUE GAS - PART 1: MEASUREMENT AT LOW CONCENTRATIONS BY USE OF IMPACTORS |
| DIN EN ISO 13199:2013-02 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF TOTAL VOLATILE ORGANIC COMPOUNDS (TVOCS) IN WASTE GASES FROM NON-COMBUSTION PROCESSES - NON-DISPERSIVE INFRARED ANALYSER EQUIPPED WITH CATALYTIC CONVERTER (ISO 13199:2012) |
| 08/30175672 DC : DRAFT SEP 2008 | BS EN 15852 - AMBIENT AIR QUALITY - STANDARD METHOD FOR THE DETERMINATION OF TOTAL GASEOUS MERCURY |
| 03/312903 DC : DRAFT SEP 2003 | EN 14792 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF NITROGEN OXIDES (NO[X]) - REFERENCE METHOD: CHEMILUMINESCENCE |
| 13/30214533 DC : 0 | BS ISO 14385-2 - STATIONARY SOURCE EMISSIONS - GREEN HOUSE GASES - PART 2: ONGOING QUALITY CONTROL OF AUTOMATED MEASURING SYSTEMS |
| 04/30126446 DC : DRAFT DEC 2004 | EN ISO 20988 - AIR QUALITY - GUIDELINES FOR ESTIMATING MEASUREMENT UNCERTAINTY |
| I.S. EN ISO 13199:2012 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF TOTAL VOLATILE ORGANIC COMPOUNDS (TVOCS) IN WASTE GASES FROM NON-COMBUSTION PROCESSES - NON-DISPERSIVE INFRARED ANALYSER EQUIPPED WITH CATALYTIC CONVERTER (ISO 13199:2012) |
| I.S. EN 1911:2010 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF GASEOUS CHLORIDES EXPRESSED AS HCL - STANDARD REFERENCE METHOD |
| I.S. EN 19694-1:2016 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 1: GENERAL ASPECTS |
| I.S. CEN TS 14793:2005 | STATIONARY SOURCE EMISSION - INTRALABORATORY VALIDATION PROCEDURE FOR AN ALTERNATIVE METHOD COMPARED TO A REFERENCE METHOD |
| ISO 17179:2016 | Stationary source emissions — Determination of the mass concentration of ammonia in flue gas — Performance characteristics of automated measuring systems |
| NF EN ISO 21258 : 2010 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF DINITROGEN MONOXIDE (N[2]O) - REFERENCE METHOD: NON-DISPERSIVE INFRARED METHOD |
| BS EN 15267-3:2007 | Air quality. Certification of automated measuring systems Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources |
| BS EN 14181:2014 | Stationary source emissions. Quality assurance of automated measuring systems |
| BS EN 14626:2012 | Ambient air. Standard method for the measurement of the concentration of carbon monoxide by non-dispersive infrared spectroscopy |
| BS EN 14791:2017 | Stationary source emissions. Determination of mass concentration of sulphur oxides. Standard reference method |
| CEN/TS 16429:2013 | Stationary source emissions - Sampling and determination of hydrogen chloride content in ducts and stacks - Infrared analytical technique |
| I.S. EN 12619:2013 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF TOTAL GASEOUS ORGANIC CARBON - CONTINUOUS FLAME IONISATION DETECTOR METHOD |
| CEN/TS 1948-5:2015 | Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 5: Long-term sampling of PCDDs/PCDFs and PCBs |
| EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
| CEN/TS 17021:2017 | Stationary source emissions - Determination of the mass concentration of sulphur dioxide by instrumental techniques |
| CEN/TS 14793:2005 | Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method |
| CEN/TR 15983:2010 | Stationary source emissions - Guidance on the application of EN 14181:2004 |
| CEN/TS 15675:2007 | Air quality - Measurement of stationary source emissions - Application of EN ISO/IEC 17025:2005 to periodic measurements |
| EN 14793:2017 | Stationary source emissions - Demonstration of equivalence of an alternative method with a reference method |
| NF EN ISO 25140 : 2010 | STATIONARY SOURCE EMISSIONS - AUTOMATIC METHOD FOR THE DETERMINATION OF THE METHANE CONCENTRATION USING FLAME IONISATION DETECTION (FID) |
| DIN EN 15852:2010-11 | Ambient air quality - Standard method for the determination of total gaseous mercury |
| 08/30161739 DC : DRAFT MAY 2008 | BS EN ISO 11771 - AIR QUALITY - DETERMINATION OF TIME-AVERAGED MASS EMISSIONS AND EMISSION FACTORS - GENERAL APPROACH |
| BS ISO 17179:2016 | Stationary source emissions. Determination of the mass concentration of ammonia in flue gas. Performance characteristics of automated measuring systems |
| PREN 14791 : DRAFT 2014 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR OXIDES - STANDARD REFERENCE METHOD |
| 11/30207395 DC : 0 | BS ISO 13199 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF TOTAL VOLATILE ORGANIC COMPOUNDS (TVOC) IN WASTE GASES FROM NON-COMBUSTION PROCESSES - NON-DISPERSIVE INFRARED METHOD EQUIPPED WITH CATALYTIC CONVERTER |
| DIN EN 15267-4:2015-08 (Draft) | AIR QUALITY - CERTIFICATION OF AUTOMATED MEASURING SYSTEMS - PART 4: PERFORMANCE CRITERIA AND TEST PROCEDURES FOR AUTOMATED MEASURING SYSTEMS FOR PERIODIC MEASUREMENTS OF EMISSIONS FROM STATIONARY SOURCES |
| PD CEN/TS 17021:2017 | Stationary source emissions. Determination of the mass concentration of sulphur dioxide by instrumental techniques |
| BS ISO 14385-2:2014 | Stationary source emissions. Greenhouse gases Ongoing quality control of automated measuring systems |
| BS EN 15852:2010 | Ambient air quality. Standard method for the determination of total gaseous mercury |
| BS EN ISO 25140:2010 | Stationary source emissions. Automatic method for the determination of the methane concentration using flame ionisation detection (FID) |
| DIN EN 14793:2017-05 | STATIONARY SOURCE EMISSIONS - DEMONSTRATION OF EQUIVALENCE OF AN ALTERNATIVE METHOD WITH A REFERENCE METHOD |
| 03/312900 DC : DRAFT SEP 2003 | EN 14789 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF VOLUME CONCENTRATION OF OXYGEN (O[2]) - REFERENCE METHOD - PARAMAGNETISM |
| 14/30303591 DC : 0 | BS EN ISO 19694-1 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 1: GENERAL ASPECTS |
| BS EN ISO 11771:2010 | Air quality. Determination of time-averaged mass emissions and emission factors. General approach |
| DD CEN/TS 14793:2005 | Stationary source emission. Intralaboratory validation procedure for an alternative method compared to a reference method |
| DD CEN/TS 15675:2007 | Air quality. Measurement of stationary source emissions. Application of EN ISO/IEC 17025:2005 to periodic measurements |
| S.R. CEN TS 15675:2007 | AIR QUALITY - MEASUREMENT OF STATIONARY SOURCE EMISSIONS - APPLICATION OF EN ISO/IEC 17025:2005 TO PERIODIC MEASUREMENTS |
| PREN 14662-3 : DRAFT 2013 | AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF BENZENE CONCENTRATIONS - PART 3: AUTOMATED PUMPED SAMPLING WITH IN SITU GAS CHROMATOGRAPHY |
| I.S. EN 15267-4:2017 | AIR QUALITY - CERTIFICATION OF AUTOMATED MEASURING SYSTEMS - PART 4: PERFORMANCE CRITERIA AND TEST PROCEDURES FOR AUTOMATED MEASURING SYSTEMS FOR PERIODIC MEASUREMENTS OF EMISSIONS FROM STATIONARY SOURCES |
| PREN 15058 : DRAFT 2014 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF CARBON MONOXIDE - STANDARD REFERENCE METHOD: NON-DISPERSIVE INFRARED SPECTROMETRY |
| DIN EN 12619:2013-04 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
| DIN EN 15267-3:2008-03 | Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources |
| DIN EN 14625:2012-12 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF OZONE BY ULTRAVIOLET PHOTOMETRY |
| DIN EN 14211:2012-11 | Ambient air - Standard method for the measurement of the concentration of nitrogen dioxide and nitrogen monoxide by chemiluminescence |
| DIN EN 14662-3:2016-02 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF BENZENE CONCENTRATIONS - PART 3: AUTOMATED PUMPED SAMPLING WITH IN SITU GAS CHROMATOGRAPHY |
| DIN EN 15259:2008-01 | Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report |
| DIN EN 14626:2012-12 | Ambient air - Standard method for the measurement of the concentration of carbon monoxide by non-dispersive infrared spectroscopy |
| BS EN 14211:2012 | Ambient air. Standard method for the measurement of the concentration of nitrogen dioxide and nitrogen monoxide by chemiluminescence |
| BS EN 14792:2017 | Stationary source emissions. Determination of mass concentration of nitrogen oxides. Standard reference method. Chemiluminescence |
| I.S. EN 14211:2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF NITROGEN DIOXIDE AND NITROGEN MONOXIDE BY CHEMILUMINESCENCE |
| I.S. EN 14792:2017 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF NITROGEN OXIDES - STANDARD REFERENCE METHOD: CHEMILUMINESCENCE |
| I.S. EN 14791:2017 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR OXIDES - STANDARD REFERENCE METHOD |
| I.S. EN 14789:2017 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF VOLUME CONCENTRATION OF OXYGEN - STANDARD REFERENCE METHOD: PARAMAGNETISM |
| I.S. EN 14625:2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF OZONE BY ULTRAVIOLET PHOTOMETRY |
| I.S. EN 14626:2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF CARBON MONOXIDE BY NON-DISPERSIVE INFRARED SPECTROSCOPY |
| I.S. EN 15058:2017 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF CARBON MONOXIDE - STANDARD REFERENCE METHOD: NON-DISPERSIVE INFRARED SPECTROMETRY |
| I.S. EN 14212:2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF SULPHUR DIOXIDE BY ULTRAVIOLET FLUORESCENCE |
| I.S. EN 14181:2014 | STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS |
| I.S. EN 14662-3:2015 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF BENZENE CONCENTRATIONS - PART 3: AUTOMATED PUMPED SAMPLING WITH IN SITU GAS CHROMATOGRAPHY |
| VDI 3462 Blatt 6:2009-03 | Emission control - Wood machining and processing - Facility-specific measuring instructions |
| I.S. EN 14884:2006 | AIR QUALITY - STATIONARY SOURCE EMISSIONS - DETERMINATION OF TOTAL MERCURY: AUTOMATED MEASURING SYSTEMS |
| VDI 4203 Blatt 3:2010-09 | Testing of automated measuring systems - Test procedures for point-related ambient air measuring systems for gaseous and particulate air pollutants |
| VDI 4220:2011-04 | Quality assurance - Requirements on bodies for the determination of air pollutants at stationary sources and in ambient air |
| VDI 3475 Blatt 5:2015-10 | Emission control - Biological waste treatment facilities - Anaerobic digestion and post-treatment |
| 13/30272419 DC : 0 | BS EN 14662-3 - AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF BENZENE CONCENTRATIONS - PART 3: AUTOMATED PUMPED SAMPLING WITH IN SITU GAS CHROMATOGRAPHY |
| PD CEN/TS 13649:2014 | Stationary source emissions. Determination of the mass concentration of individual gaseous organic compounds. Sorptive sampling method followed by solvent extraction or thermal desorption |
| I.S. EN 15852:2010 | AMBIENT AIR QUALITY - STANDARD METHOD FOR THE DETERMINATION OF TOTAL GASEOUS MERCURY |
| 15/30289059 DC : 0 | BS ISO 17179 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF AMMONIA IN FLUE GAS - PERFORMANCE CHARACTERISTICS OF AUTOMATED MEASURING SYSTEMS |
| BS EN ISO 16911-2:2013 | Stationary source emissions. Manual and automatic determination of velocity and volume flow rate in ducts Automated measuring systems |
| BS EN 15267-4:2017 | Air quality. Certification of automated measuring systems Performance criteria and test procedures for automated measuring systems for periodic measurements of emissions from stationary sources |
| PD CEN/TS 16429:2013 | Stationary source emissions. Sampling and determination of hydrogen chloride content in ducts and stacks. Infrared analytical technique |
| BS EN ISO 21258:2010 | Stationary source emissions. Determination of the mass concentration of dinitrogen monoxide (N2O). Reference method. Non-dispersive infrared method |
| 14/30293544 DC : 0 | BS EN 14791 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR OXIDES - STANDARD REFERENCE METHOD |
| 18/30319123 DC : 0 | BS ISO 20264 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF INDIVIDUAL VOLATILE ORGANIC COMPOUNDS (VOCS) IN WASTE GASES FROM NON-COMBUSTION PROCESSES |
| 03/312901 DC : DRAFT SEP 2003 | EN 14790 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE WATER VAPOUR IN DUCTS |
| 03/306307 DC : DRAFT JUNE 2003 | EN 14626 - AMBIENT AIR QUALITY - MEASUREMENT METHOD FOR THE DETERMINATION OF CARBON MONOXIDE IN AMBIENT AIR BY MEANS OF THE NON-DISPERSIVE INFRARED METHOD |
| I.S. EN ISO 23210:2009 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF PM[10]/PM[2,5] MASS CONCENTRATION IN FLUE GAS - MEASUREMENT AT LOW CONCENTRATIONS BY USE OF IMPACTORS |
| I.S. CEN/TS 17021:2017 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF SULPHUR DIOXIDE BY INSTRUMENTAL TECHNIQUES |
| S.R. CEN/TR 17078:2017 | STATIONARY SOURCE EMISSIONS - GUIDANCE ON THE APPLICATION OF EN ISO 16911-1 |
| ISO 14385-2:2014 | Stationary source emissions — Greenhouse gases — Part 2: Ongoing quality control of automated measuring systems |
| ISO 23552-1:2007 | Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type |
| DIN EN 14181:2015-02 | Stationary source emissions - Quality assurance of automated measuring systems |
| DIN EN 14212:2012-11 | Ambient air - Standard method for the measurement of the concentration of sulphur dioxide by ultraviolet fluorescence; German version EN 14212:2012 |
| DIN EN 14792:2006-04 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF NITROGEN OXIDES - STANDARD REFERENCE METHOD: CHEMILUMINESCENCE |
| EN 14662-3:2015 | Ambient air - Standard method for the measurement of benzene concentrations - Part 3: Automated pumped sampling with in situ gas chromatography |
| DIN EN 1911:2010-12 | Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method |
| DIN EN ISO 11771:2011-04 | Air quality - Determination of time-averaged mass emissions and emission factors - General approach (ISO 11771:2010) |
| 08/30184648 DC : DRAFT SEP 2008 | BS EN 15859 - AIR QUALITY - CERTIFICATION OF AUTOMATED DUST ARRESTMENT PLANT MONITORS FOR USE ON STATIONARY SOURCES - PERFORMANCE CRITERIA AND TEST PROCEDURES |
| BS EN 19694-1:2016 | Stationary source emissions. Determination of greenhouse gas (GHG) emissions in energy-intensive industries General aspects |
| DIN EN ISO 23210:2009-12 | Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009) |
| BS EN ISO 15796:2008 | Gas analysis. Investigation and treatment of analytical bias |
| 14/30293541 DC : 0 | BS EN 14789 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF VOLUME CONCENTRATION OF OXYGEN (O2) - STANDARD REFERENCE METHOD - PARAMAGNETISM |
| DIN EN ISO 16911-2:2013-06 | STATIONARY SOURCE EMISSIONS - MANUAL AND AUTOMATIC DETERMINATION OF VELOCITY AND VOLUME FLOW RATE IN DUCTS - PART 2: AUTOMATED MEASURING SYSTEMS (ISO 16911-2:2013) |
| 15/30318313 DC : 0 | BS EN 15267-4 - AIR QUALITY - CERTIFICATION OF AUTOMATED MEASURING SYSTEMS - PART 4: PERFORMANCE CRITERIA AND TEST PROCEDURES FOR AUTOMATED MEASURING SYSTEMS FOR PERIODIC MEASUREMENTS OF EMISSIONS FROM STATIONARY SOURCE |
| BS ISO 14385-1:2014 | Stationary source emissions. Greenhouse gases Calibration of automated measuring systems |
| BS EN 14793:2017 | Stationary source emissions. Demonstration of equivalence of an alternative method with a reference method |
| 08/30158227 DC : DRAFT JUNE 2008 | BS EN ISO 21258 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF DINITROGEN MONOXIDE - REFERENCE METHOD - NON-DISPERSIVE INFRARED METHOD |
| BS EN ISO 16911-1:2013 | Stationary source emissions. Manual and automatic determination of velocity and volume flow rate in ducts Manual reference method |
| BS EN 1911:2010 | Stationary source emissions. Determination of mass concentration of gaseous chlorides expressed as HCl. Standard reference method |
| BS ISO 15796 : 2005 | GAS ANALYSIS - INVESTIGATION AND TREATMENT OF ANALYTICAL BIAS |
| DIN EN ISO 25140:2010-12 | Stationary source emissions - Automatic method for the determination of the methane concentration using flame ionisation detection (FID) (ISO 25140:2010) |
| DIN EN ISO 15796:2008-11 | GAS ANALYSIS - INVESTIGATION AND TREATMENT OF ANALYTICAL BIAS |
| S.R. CEN/TS 13649:2014 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF INDIVIDUAL GASEOUS ORGANIC COMPOUNDS - SORPTIVE SAMPLING METHOD FOLLOWED BY SOLVENT EXTRACTION OR THERMAL DESORPTION |
| I.S. EN ISO 16911-2:2013 | STATIONARY SOURCE EMISSIONS - MANUAL AND AUTOMATIC DETERMINATION OF VELOCITY AND VOLUME FLOW RATE IN DUCTS - PART 2: AUTOMATED MEASURING SYSTEMS (ISO 16911-2:2013) |
| I.S. EN ISO 21258:2010 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF DINITROGEN MONOXIDE (N[2]O) - REFERENCE METHOD: NON-DISPERSIVE INFRARED METHOD |
| PREN 14789 : DRAFT 2014 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF VOLUME CONCENTRATION OF OXYGEN - STANDARD REFERENCE METHOD: PARAMAGNETISM |
| PREN ISO 13199 : DRAFT 2011 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF TOTAL VOLATILE ORGANIC COMPOUNDS (TVOC) IN WASTE GASES FROM NON-COMBUSTION PROCESSES - NON-DISPERSIVE INFRARED METHOD EQUIPPED WITH CATALYTIC CONVERTER |
| ISO 13271:2012 | Stationary source emissions — Determination of PM10/PM2,5 mass concentration in flue gas — Measurement at higher concentrations by use of virtual impactors |
| I.S. EN ISO 15796:2008 | GAS ANALYSIS - INVESTIGATION AND TREATMENT OF ANALYTICAL BIAS |
| S.R. CWA 16060:2009 | ENVIRONMENTAL TECHNOLOGY VERIFICATION - AIR EMISSION ABATEMENT TECHNOLOGIES |
| I.S. EN ISO 25140:2010 | STATIONARY SOURCE EMISSIONS - AUTOMATIC METHOD FOR THE DETERMINATION OF THE METHANE CONCENTRATION USING FLAME IONISATION DETECTION (FID) |
| BS EN 15058:2017 | Stationary source emissions. Determination of the mass concentration of carbon monoxide. Standard reference method: non-dispersive infrared spectrometry |
| ISO 25140:2010 | Stationary source emissions — Automatic method for the determination of the methane concentration using flame ionisation detection (FID) |
| BS EN 14789:2017 | Stationary source emissions. Determination of volume concentration of oxygen. Standard reference method: Paramagnetism |
| BS EN 12619:2013 | Stationary source emissions. Determination of the mass concentration of total gaseous organic carbon. Continuous flame ionisation detector method |
| ISO 15796:2005 | Gas analysis — Investigation and treatment of analytical bias |
| BS EN 14662-3:2015 | Ambient air. Standard method for the measurement of benzene concentrations Automated pumped sampling with in situ gas chromatography |
| ISO 16911-1:2013 | Stationary source emissions — Manual and automatic determination of velocity and volume flow rate in ducts — Part 1: Manual reference method |
| BS EN 14884:2005 | Air quality. Stationary source emissions. Determination of total mercury: automated measuring systems |
| BS EN 14625:2012 | Ambient air. Standard method for the measurement of the concentration of ozone by ultraviolet photometry |
| ISO 21258:2010 | Stationary source emissions — Determination of the mass concentration of dinitrogen monoxide (N2O) — Reference method: Non-dispersive infrared method |
| ISO 11771:2010 | Air quality — Determination of time-averaged mass emissions and emission factors — General approach |
| ISO 23210:2009 | Stationary source emissions — Determination of PM10/PM2,5 mass concentration in flue gas — Measurement at low concentrations by use of impactors |
| ISO 16911-2:2013 | Stationary source emissions — Manual and automatic determination of velocity and volume flow rate in ducts — Part 2: Automated measuring systems |
| ISO 13199:2012 | Stationary source emissions — Determination of total volatile organic compounds (TVOCs) in waste gases from non-combustion processes — Non-dispersive infrared analyser equipped with catalytic converter |
| DIN EN 15058:2006-09 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF CARBON MONOXIDE - STANDARD REFERENCE METHOD: NON-DISPERSIVE INFRARED SPECTROMETRY |
| DIN EN 14791:2006-04 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR OXIDES - STANDARD REFERENCE METHOD |
| EN ISO 16911-2:2013 | Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 2: Automated measuring systems (ISO 16911-2:2013) |
| EN ISO 23210:2009 | Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009) |
| EN 1911:2010 | Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method |
| EN ISO 15796:2008 | Gas analysis - Investigation and treatment of analytical bias (ISO 15796:2005) |
| EN ISO 13199:2012 | Stationary source emissions - Determination of total volatile organic compounds (TVOCs) in waste gases from non-combustion processes - Non-dispersive infrared analyser equipped with catalytic converter (ISO 13199:2012) |
| EN ISO 25140:2010 | Stationary source emissions - Automatic method for the determination of the methane concentration using flame ionisation detection (FID) (ISO 25140:2010) |
| EN 14789:2017 | Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism |
| EN ISO 21258:2010 | Stationary source emissions - Determination of the mass concentration of dinitrogen monoxide (N2O) - Reference method: Non-dispersive infrared method (ISO 21258:2010) |
| EN 15058:2017 | Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry |
| EN 15852:2010 | Ambient air quality - Standard method for the determination of total gaseous mercury |
| EN 14626:2012 | Ambient air - Standard method for the measurement of the concentration of carbon monoxide by non-dispersive infrared spectroscopy |
| EN 19694-1:2016 | Stationary source emissions - Determination of greenhouse gas (GHG) emissions in energy-intensive industries - Part 1: General aspects |
| EN 14791:2017 | Stationary source emissions - Determination of mass concentration of sulphur oxides - Standard reference method |
| EN 15259:2007 | Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report |
| EN 14884:2005 | Air quality - Stationary source emissions - Determination of total mercury: automated measuring systems |
| EN 15267-4:2017 | Air quality - Certification of automated measuring systems - Part 4: Performance criteria and test procedures for automated measuring systems for periodic measurements of emissions from stationary sources |
| EN ISO 16911-1:2013 | Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 1: Manual reference method (ISO 16911-1:2013) |
| EN 15267-3:2007 | Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources |
| EN ISO 11771:2010 | Air quality - Determination of time-averaged mass emissions and emission factors - General approach (ISO 11771:2010) |
| EN 14211:2012 | Ambient air - Standard method for the measurement of the concentration of nitrogen dioxide and nitrogen monoxide by chemiluminescence |
| EN 14181:2014 | Stationary source emissions - Quality assurance of automated measuring systems |
| EN 14625:2012 | Ambient air - Standard method for the measurement of the concentration of ozone by ultraviolet photometry |
| ISO 14385-1:2014 | Stationary source emissions — Greenhouse gases — Part 1: Calibration of automated measuring systems |
| PD CEN/TR 17078:2017 | Stationary source emissions. Guidance on the application of EN ISO 16911-1 |
| DIN EN ISO 21258:2010-11 | Stationary source emissions - Determination of the mass concentration of dinitrogen monoxide (N<(Index)2>O) - Reference method: Non-dispersive infrared method (ISO 21258:2010) |
| 03/306306 DC : DRAFT JUNE 2003 | EN 14625 - AMBIENT AIR QUALITY - MEASUREMENT METHOD FOR THE DETERMINATION OF OZONE IN AMBIENT AIR BY MEANS OF ULTRAVIOLET PHOTOMETRIC METHOD |
| 14/30293538 DC : 0 | BS EN 14793 - STATIONARY SOURCE EMISSIONS - DEMONSTRATION OF EQUIVALENCE OF AN ALTERNATIVE METHOD WITH THE REFERENCE METHOD |
| 12/30259213 DC : 0 | BS EN 14181 - STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS |
| DIN EN ISO 16911-1:2013-06 | Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 1: Manual reference method (ISO 16911-1:2013); German version EN ISO 16911-1:2013 |
| 14/30293554 DC : 0 | BS EN 15058 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF CARBON MONOXIDE - STANDARD REFERENCE METHOD: NON-DISPERSIVE INFRARED SPECTROMETRY |
| BS EN ISO 23210:2009 | Stationary source emissions. Determination of PM10/PM2,5 mass concentration in flue gas. Measurement at low concentrations by use of impactors |
| BS EN ISO 13199:2012 | Stationary source emissions. Determination of total volatile organic compounds (TVOCs) in waste gases from non-combustion processes. Non-dispersive infrared analyser equipped with catalytic converter |
| BS ISO 13271:2012 | Stationary source emissions. Determination of PM10/PM2,5 mass concentration in flue gas. Measurement at higher concentrations by use of virtual impactors |
| 03/312902 DC : DRAFT SEP 2003 | EN 14791 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR DIOXIDE - REFERENCE METHOD |
| S.R. CEN/TS 1948-5:2015 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF PCDDS/PCDFS AND DIOXIN-LIKE PCBS - PART 5: LONG-TERM SAMPLING OF PCDDS/PCDFS AND PCBS |
| S.R. CEN TR 15983:2010 | STATIONARY SOURCE EMISSIONS - GUIDANCE ON THE APPLICATION OF EN 14181:2004 |
| I.S. EN ISO 16911-1:2013 | STATIONARY SOURCE EMISSIONS - MANUAL AND AUTOMATIC DETERMINATION OF VELOCITY AND VOLUME FLOW RATE IN DUCTS - PART 1: MANUAL REFERENCE METHOD (ISO 16911-1:2013) |
| I.S. EN 14793:2017 | STATIONARY SOURCE EMISSIONS - DEMONSTRATION OF EQUIVALENCE OF AN ALTERNATIVE METHOD WITH A REFERENCE METHOD |
| S.R. CEN/TS 16429:2013 | STATIONARY SOURCE EMISSIONS - SAMPLING AND DETERMINATION OF HYDROGEN CHLORIDE CONTENT IN DUCTS AND STACKS - INFRARED ANALYTICAL TECHNIQUE |
| EN 14792:2017 | Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence |
| I.S. EN ISO 11771:2010 | AIR QUALITY - DETERMINATION OF TIME-AVERAGED MASS EMISSIONS AND EMISSION FACTORS - GENERAL APPROACH |
| BS EN 14212:2012 | Ambient air. Standard method for the measurement of the concentration of sulphur dioxide by ultraviolet fluorescence |
| BS EN 15259:2007 | Air quality. Measurement of stationary source emissions. Requirements for measurement sections and sites and for the measurement objective, plan and report |
| CEN/TS 13649:2014 | Stationary source emissions - Determination of the mass concentration of individual gaseous organic compounds - Sorptive sampling method followed by solvent extraction or thermal desorption |
| CEN/TR 17078:2017 | Stationary source emissions - Guidance on the application of EN ISO 16911-1 |
| UNE-EN 15852:2010 | Ambient air quality - Standard method for the determination of total gaseous mercury |
| UNE-CEN/TR 15983:2011 IN | Stationary source emissions - Guidance on the application of EN 14181:2004 |
| UNE-EN ISO 21258:2010 | Stationary source emissions - Determination of the mass concentration of dinitrogen monoxide (N2O) - Reference method: Non-dispersive infrared method (ISO 21258:2010) |
| UNE-EN 1911:2011 | Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method |
| UNE-EN ISO 11771:2011 | Air quality - Determination of time-averaged mass emissions and emission factors - General approach (ISO 11771:2010) |
| UNE-EN ISO 16911-2:2014 | Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 2: Automated measuring systems (ISO 16911-2:2013) |
| UNE-CWA 16060:2010 IN | Environmental technology verification - Air emission abatement technologies |
| UNE-EN ISO 23210:2010 | Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009) |
| UNE-EN ISO 25140:2011 | Stationary source emissions - Automatic method for the determination of the methane concentration using flame ionisation detection (FID) (ISO 25140:2010) |
| UNE-EN 14625:2013 | Ambient air - Standard method for the measurement of the concentration of ozone by ultraviolet photometry |
| UNE-EN 14212:2013 | Ambient air - Standard method for the measurement of the concentration of sulphur dioxide by ultraviolet fluorescence |
| UNE-EN 14626:2013 | Ambient air - Standard method for the measurement of the concentration of carbon monoxide by non-dispersive infrared spectroscopy |
| UNE-EN 14793:2017 | Stationary source emissions - Demonstration of equivalence of an alternative method with a reference method |
| UNE-EN 15058:2017 | Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry |
| UNE-EN 14662-3:2016 | Ambient air - Standard method for the measurement of benzene concentrations - Part 3: Automated pumped sampling with in situ gas chromatography |
| UNE-EN ISO 13199:2013 | Stationary source emissions - Determination of total volatile organic compounds (TVOCs) in waste gases from non-combustion processes - Non-dispersive infrared analyser equipped with catalytic converter (ISO 13199:2012) |
| ONORM EN 14212 : JUL 2014 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF SULPHUR DIOXIDE BY ULTRAVIOLET FLUORESCENCE |
| UNE-EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
| UNE-EN 14791:2017 | Stationary source emissions - Determination of mass concentration of sulphur oxides - Standard reference method |
| UNE-EN 15267-4:2018 | Air quality - Certification of automated measuring systems - Part 4: Performance criteria and test procedures for automated measuring systems for periodic measurements of emissions from stationary sources |
| UNE-EN 14181:2015 | Stationary source emissions - Quality assurance of automated measuring systems |
| UNE-EN 14211:2013 | Ambient air - Standard method for the measurement of the concentration of nitrogen dioxide and nitrogen monoxide by chemiluminescence |
| ONORM EN 14625 : 2013 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF OZONE BY ULTRAVIOLET PHOTOMETRY |
| ONORM EN 14211 : 2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF NITROGEN DIOXIDE AND NITROGEN MONOXIDE BY CHEMILUMINESCENCE |
| ONORM EN 14626 : 2012 | AMBIENT AIR - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF CARBON MONOXIDE BY NON-DISPERSIVE INFRARED SPECTROSCOPY |
| UNE-EN ISO 16911-1:2013 | Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 1: Manual reference method (ISO 16911-1:2013) |
| UNE-EN 14789:2017 | Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism |
| I.S. EN 15267-3:2007 | AIR QUALITY - CERTIFICATION OF AUTOMATED MEASURING SYSTEMS - PART 3: PERFORMANCE CRITERIA AND TEST PROCEDURES FOR AUTOMATED MEASURING SYSTEMS FOR MONITORING EMISSIONS FROM STATIONARY SOURCES |
| ISO 7935:1992 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods |
| ISO 6879:1995 | Air quality — Performance characteristics and related concepts for air quality measuring methods |
| ISO 11222:2002 | Air quality — Determination of the uncertainty of the time average of air quality measurements |
| ISO 9169:2006 | Air quality — Definition and determination of performance characteristics of an automatic measuring system |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.