IEC 62677-1:2017
Current
The latest, up-to-date edition.
Heat shrinkable low and medium voltage moulded shapes - Part 1: General requirements
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English - French
11-10-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Moulded shape material specimens
5 Classification
6 Ordering
7 Dimensions
8 Colour
9 Finish
10 Packaging
11 Labelling
12 Qualification approval requirements
13 Consignment tests
Annex A (informative) - Heat shrinkable
moulded parts (typical configuration)
Bibliography
IEC 62677-1:2017 is applicable to heat shrinkable low and medium voltage moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection, electrical conductance, anti-tracking and strain relief for power cable terminations, joints and stop ends. It specifies the test methods and material requirements. The most commonly available shapes are as shown in the Annex A. Materials which conform to this document meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and will not be based on this document alone. These moulded shapes are designed to be used in low and medium voltage cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in EN 50393, HD 629.1 and IEC 60502-4.
| Committee |
TC 15
|
| DevelopmentNote |
Stability Date: 2020. (10/2017)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Current
|
| Standards | Relationship |
| BS EN IEC 62677-1:2018 | Identical |
| NF EN 62677-1 : 2012 PR | Identical |
| EN IEC 62677-1:2018 | Identical |
| NEN EN IEC 62677-1 : 2018 | Identical |
| DIN EN IEC 62677-1 : 2018 | Identical |
| I.S. EN IEC 62677-1:2018 | Identical |
| UNE-EN IEC 62677-1:2018 | Identical |
| NF EN IEC 62677-1 : 2018 | Identical |
| VDE 0343-1 : 2018 | Identical |
| 14/30267388 DC : 0 | BS EN 62677-2 ED 1.0 - HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 2: METHODS OF TEST |
| EN IEC 62677-2:2018 | Heat shrinkable low and medium voltage moulded shapes - Part 2 Methods of test |
| BS EN IEC 62677-3-102:2018 | Heat-shrinkable low and medium voltage moulded shapes Specification for individual materials. Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications |
| I.S. EN IEC 62677-2:2018 | HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 2: METHODS OF TEST |
| IEC 62677-3-101:2018 | Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications |
| 15/30324023 DC : 0 | BS EN 62677-3-102 ED. 1.0 - HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 3: MATERIAL REQUIREMENTS - SHEET 102: HEAT-SHRINKABLE, POLYOLEFIN, ANTI-TRACKING MOULDED SHAPES FOR MEDIUM VOLTAGE APPLICATIONS |
| EN IEC 62677-3-102:2018 | Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications |
| BS EN IEC 62677-3-101:2018 | Heat-shrinkable low and medium voltage moulded shapes Specification for individual materials. Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications |
| I.S. EN IEC 62677-3-102:2018 | HEAT-SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 3: SPECIFICATION FOR INDIVIDUAL MATERIALS - SHEET 102: HEAT-SHRINKABLE, POLYOLEFIN, ANTI-TRACKING MOULDED SHAPES FOR MEDIUM VOLTAGE APPLICATIONS |
| IEC 62677-2:2017 | Heat shrinkable low and medium voltage moulded shapes - Part 2: Methods of test |
| IEC 62677-3-102:2018 | Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications |
| 15/30324018 DC : 0 | BS EN 62677-3-101 ED. 1.0 - HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 3: MATERIAL REQUIREMENTS - SHEET 101: HEAT-SHRINKABLE, POLYOLEFIN MOULDED SHAPES FOR LOW VOLTAGE APPLICATIONS |
| EN IEC 62677-3-101:2018 | Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications |
| I.S. EN IEC 62677-3-101:2018 | HEAT-SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 3: SPECIFICATION FOR INDIVIDUAL MATERIALS - SHEET 101: HEAT-SHRINKABLE, POLYOLEFIN MOULDED SHAPES FOR LOW VOLTAGE APPLICATIONS |
| IEC 62677-2:2017 | Heat shrinkable low and medium voltage moulded shapes - Part 2: Methods of test |
| IEC 60502-4:2010 | Power cables with extruded insulation and their accessories for rated voltages from 1 kV (U<sub>m</sub> = 1,2 kV) up to 30 kV (U<sub>m</sub> = 36 kV) - Part 4: Test requirements on accessories for cables with rated voltages from 6 kV (U<sub>m</sub> = 7,2 kV) up to 30 kV (U<sub>m</sub> = 36 kV) |
| IEC 60050-212:2010 | International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases |
| EN 50393:2015 | Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV |
| HD 629.1 S2:2006/A1:2008 | TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 1: CABLES WITH EXTRUDED INSULATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.