IEC 60512-6:1984
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests
Available format(s)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
04-05-2012
Superseded by
Language(s)
English - French
Published date
30-08-1984
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Contents
Foreword
Preface
Scope
Section One - Climatic Tests
Clause
1. Test 11a: Climatic sequence
2. Test 11b: Combined/sequential cold, low air pressure
and damp heat
3. Test 11c: Damp heat, steady state
4. Test 11d: Rapid change of temperature
5. Test 11e: Mould growth
6. Test 11f: Corrosion, salt mist
7. Test 11g: Corrosion, industrial atmosphere (under
consideration)
8. Test 11h: Sand and dust (under consideration)
9. Test 11i: Dry heat
10. Test 11j: Cold
11. Test 11k: Low air pressure
12. Test 11m: Damp heat, cyclic
13. Test 11n: Gas tightness, solderless wrapped connections
Section Two - Soldering Tests
14. Test 12a: Solderability, wetting, solder bath method
15. Test 12b: Solderability, wetting, iron method
16. Test 12c: Solderability, dewetting
17. Test 12d: Resistance to soldering heat, solder bath
method
18 Test 12e: Resistance to soldering heat, iron method
The tests contained in this standard, when required by the detail specification, shall be used for electromechanical components having an inherent connecting or switching function intended for use in equipment for telecommunication and in electronic devices employing similar techniques.
| Committee |
TC 48/SC 48B
|
| DevelopmentNote |
Also numbered as BS 5772-6(1984) (08/2005)
|
| DocumentType |
Standard
|
| Pages |
53
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE 20606-6:1986 | Identical |
| DIN IEC 60512-6:1994-05 | Identical |
| AS 3726.6-1989 | Identical |
| NEN 10512-6 : 1985 | Identical |
| CEI 48-12 : 1998 | Identical |
| NFC 93 400 : 85 AMD 1 88 | Identical |
| CEI 48-5 : 1ED 1983 | Identical |
| BS EN 61076-7:2001 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications Cable outlet accessories with assessed quality, including qualification and capability approval. Sectional specification |
| BS EN 60603-1:2000 | Connectors for frequencies below 3 MHz for use with printed boards Generic specification. General requirements and guide for the preparation of detail specifications with assessed quality |
| I.S. CECC 75301-802:1995 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| BS EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| FD ISO/TR 12369 : 2001 FD | AGRICULTURAL TRACTORS AND MACHINERY - ELECTRICAL POWER TRANSMISSION CONNECTORS |
| 03/100395 DC : DRAFT APR 2003 | EN 175101-809 - DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| 02/202649 DC : DRAFT JAN 2002 | IEC PAS 61076-3-111. ED.1 - CONNECTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 3-111: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED AND UNSHIELDED, FREE AND FIXED CONNECTORS, FOR INDUSTRIAL ENVIRONMENTS FOR FREQUENCIES UP TO 250 MHZ |
| IEC 60131-1:1984 | Lever switches. Part 1: General requirements and rules for the preparation of detail specifications |
| UNE-EN 50467:2012 | Railway applications - Rolling stock - Electrical connectors, requirements and test methods |
| I.S. EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| CEI 48-20 : 1998 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 3: DETAIL SPECIFICATION FOR A RANGE OF CONNECTORS WITH TRAPEZOIDAL SHAPED METAL SHELLS AND ROUND CONTACTS - REMOVABLE CRIMP CONTACT TYPES WITH CLOSED CRIMP BARRELS, REAR INSERTION/REAR EXTRACTION |
| EN 61076-5 : 2001 | CONNECTORS FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 5: IN-LINE SOCKETS WITH ASSESSED QUALITY - SECTIONAL SPECIFICATION |
| EN 196000 : 92 AMD 1 2001 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: ELECTROMECHANICAL SWITCHES |
| EN 60603-12:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 12: Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| NF EN 60352-3 : 2002 | SOLDERLESS CONNECTIONS - PART 3: SOLDERLESS ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 105: Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| EN 61076-7:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 7: Cable outlet accessories with assessed quality, including qualification and capability approval - Sectional specification |
| EN 60130-17:1999 | Connectors for frequencies below 3 MHz - Part 17: Detail specification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| CEI 13-32 : 2000 | WATT-VAR-HOUR METERS FOR LOW-VOLTAGE THREE-PHASE NETWORKS (INTEGRATED UNITS) PRESETTED FOR PROCESSING AND REMOTE MANAGEMENT OF DATA WITH OR WITHOUT INSERTION OF CURRENT TRANSFORMERS |
| BS EN 60130-17:1999 | Connectors for frequencies below 3 MHz Detail specification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| BS EN 196403:2000 | Harmonized systems of quality assessment for electronic components. Blank detail specification: push button switches. Assessment level Y |
| BS EN 60352-6:1998 | Solderless connections Solderless insulation piercing connections. General requirements, test methods and practical guidance |
| 00/201724 DC : DRAFT APR 2000 | IEC 61076-1 - CONNECTORS - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| BS EN 61076-4-104:1999 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm - Detail specification for two part modular connectors (with optional shielding plates) for printed boards and backplanes, basic grid 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| CEI EN 50467 : 2013 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 04/30112325 DC : DRAFT APR 2004 | IEC 61076-3-104 ED.2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-104: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 1000 MHZ |
| BS EN 196000:1993 | Harmonized system of quality assessment for electronic components. Generic specification. Electromechanical switches |
| PREN 50467 : DRAFT 2009 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| BS EN 60352-1:1998 | Solderless connections Wrapped connections. General requirements, test methods and practical guidance |
| CEI EN 60352-3 : 1996 | SOLDERLESS CONNECTIONS - PART 3: SOLDERLESS ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| I.S. EN 60603-2:1998 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| CEI EN 60603-1 : 2001 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 1: GENERIC SPECIFICATION; GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY |
| IEC PAS 61076-3-110:2002 | Connectors for electronic equipment - Part 3-110: Detail specification for 8 way connectors for frequencies up to 600 MHz |
| IEC 60130-17:1998 | Connectors for frequencies below 3 MHz - Part 17: Detailspecification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| IEC 61076-4-105:1995 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 105 : Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication . |
| IEC 61020-6:1991 | Electromechanical switches for use in electronic equipment - Part 6: Sectional specification for sensitive switches |
| EN 196110 : 2002 | SECTIONAL SPECIFICATION - ROTARY SWITCHES - CAPABILITY APPROVAL |
| BS EN 60603-2:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features |
| BS EN 196103:2000 | Blank detail specification: Rotary switches. Assessment level Y |
| DD CLC/TS 50467:2008 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| CECC 75301-802 : 1994 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| BS EN 60603-12:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| BS EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| 98/230855 DC : DRAFT APRIL 1998 | IEC 61076-4-112 - CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C, LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 112 - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS FOR PRINTED BOARDS FOR BASIC GRID OF 2,00 MM, WITH SQUARE MALE CONTACTS OF 0,50 X 0,50 MM |
| I.S. EN 60130-17:1999 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 17: DETAIL SPECIFICATION FOR INTERCONNECTION DEVICES WHICH PERMIT MULTI-DIRECTIONAL MATING, FOR USE WITH RECHARGEABLE BATTERIES |
| I.S. EN 61076-5:2002 | CONNECTORS FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 5: IN-LINE SOCKETS WITH ASSESSED QUALITY - SECTIONAL SPECIFICATION |
| IEC 60131-4:1987 | Lever switches. Part 4: Requirements for miniature toggle switches |
| CECC 75101-807 : 1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRIDOF 2.5 mm - ACCORDING TO IEC 917 (DETAIL SPECIFICATION) |
| IEC PAS 61076-3-109:2001 | Connectors for electronic equipment - Part 3-109: Detail specification for two-part cable to board connector for high speed data application in a harsh industrial environment - Protection rate IP67 according to IEC 60529 |
| IEC 61020-3-2:1995 | Electromechanical switches for use in electronic equipment - Part3: Sectional specification for in-line package switches - Section2: Detail specification for dual-in-line package (DIP) switches,raised and recessed rocker actuated |
| I.S. CECC 75101-807:1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRID OF 2.5 MM - (ACCORDING TO IEC 917) (DETAIL SPECIFICATION) |
| S.R. CLC/TS 50467:2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 175101-809:2004/corrigendum Jun. 2005 | DETAIL SPECIFICATION: TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| NF EN 60352-4 : 2001 | SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| EN 60352-3:1994 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| EN 60352-4:1994/A1:2000 | SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| CEI 48-19 : 1998 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 2: DETAIL SPECIFICATION FOR A RANGE OF CONNECTORS, WITH ASSESSED QUALITY, WITH TRAPEZOIDAL SHAPED METAL SHELLS AND ROUND CONTACTS - FIXED SOLDER CONTACT TYPES |
| BS EN 60603-5:1998 | Connectors for frequencies below 3 MHz for use with printed boards Edge-socket connectors and two-part connectors for double-sided printed boards with 2,54 mm (0,1 mm) spacing |
| ISO/IEC 14575:2000 | Information technology — Microprocessor systems — Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction) |
| CEI EN 60130-17 : 2001 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 17: DETAIL SPECIFICATION FOR INTERCONNECTION DEVICES WHICH PERMIT MULTI-DIRECTIONAL MATING, FOR USE WITH RECHARGEABLE BATTERIES |
| CEI EN 60352-6 : 1998 | SOLDERLESS CONNECTIONS - PART 6: INSULATION PIERCING CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| BS QC 480000(1995) : 1995 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 1: GENERIC SPECIFICATION |
| ANSI INCITS 293 : 1996 : R2006 | INFORMATION TECHNOLOGY - SERIAL STORAGE ARCHITECTURE PHYSICAL LAYER 1 (SSA-PH1) |
| BS EN 175101-802:2000 | Harmonized system of quality assessment for electronic components. Detail specification Two-part connectors for printed boards for high number of contacts with basic grid of 2,54 mm on 3 or 4 rows |
| BS EN 60352-4:1995 | Solderless connections Solderless non-accessible insulation displacement connections. General requirements, test methods and practical guidance |
| NF EN 61076 4 105 : 1999 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 105: DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION AND AUDIO INDUSTRY |
| 03/100336 DC : DRAFT MAR 2003 | IEC 60603-7-7 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-7: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 600 MHZ |
| 03/100165 DC : DRAFT JAN 2003 | IEC 60603-7-2 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-2: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ |
| ANSI INCITS 293 : 1996 : R2001 | INFORMATION TECHNOLOGY - SERIAL STORAGE ARCHITECTURE PHYSICAL LAYER 1 (SSA-PH1) |
| I.S. EN 196110:2002 | SECTIONAL SPECIFICATION: ROTARY SWITCHES - CAPABILITY APPROVAL |
| I.S. EN 61076-4-104:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM |
| CEI EN 60352-1 : 1998 | SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| CEI 13-26 : 1999 | WATT-HOUR METERS AND POWER LIMITERS FOR LOW-VOLTAGE NETWORKS (INTEGRATED UNITS) PERMITTED OR NOT FOR PROCESSING AND REMOTE MANAGEMENT OF DATA |
| IEC 60352-3:1993 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| IEC 61076-5:2001 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications - Part 5: In-line sockets with assessed quality - Sectional specification |
| IEC 61020-5:1991 | Electromechanical switches for use in electronic equipment - Part 5: Sectional specification for pushbutton switches |
| IEC 60352-6:1997 | Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance |
| IEC PAS 61076-3-111:2002 | Connectors for electronic equipment - Part 3-111: Detail specification for 8-way, shielded and unshielded, free and fixed connectors, for industrial environments for frequencies up to 250 MHz |
| IEC 61076-4-101:2001 | Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| IEC 61076-4-100:2001 | Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| IEC 60603-12:1992 | Connectors for frequencies below 3 MHz for use with printed boards - Part 12: Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| IEC 61076-3-100:1999 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| CLC/TS 50467 : 2008 COR 2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| DIN EN 60352-1:1998-04 | SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| 01/207165 DC : DRAFT OCT 2001 | IEC 61076-3-110 ED.1 - CONNECTORS FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED APPLICATIONS - PART 3-110: DETAIL SPECIFICATION FOR 8 WAY CONNECTORS FOR FREQUENCIES UP TO 600 MHZ [CATEGORY 7 DETAIL SPECIFICATION] |
| BS EN 61076-5:2001 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications In-line sockets with assessed quality. Sectional specification |
| BS EN 60603-6:1998 | Connectors for frequencies below 3 MHz for use with printed boards Edge-socket connectors and printed board connectors with 2,54 mm (0,1 in) contact spacing for single or double-sided printed boards of 1,6 mm (0,063 in) nominal thickness |
| 09/30208429 DC : 0 | BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| BS QC010000(1993) : AMD 10432 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS. CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE WITH PRINTED BOARDS - GENERIC SPECIFICATION: GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY |
| CEI EN 61076-4-104 : 2001 | CONNECTORS FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GIRD OF 2,0 MMS WITH TERMINATIONS ON A MULTIPLE GIRD OF 0,5 MM |
| BS EN 50467:2011 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| BS EN 175101-809:2004 | Harmonized system of quality assessment for electronic components. Detail specification Two-part connectors for printed boards having a grid of 2,54 mm, short version in compliance with CECC 75 101-801, with assessed quality |
| 01/206171 DC : DRAFT AUG 2001 | |
| IEC PAS 61076-3-104:2002 | Connectors for electronic equipment - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors, for data transmissions with frequencies up to 600 MHz minimum |
| DIN EN 60352-3:1995-05 | Solderless connections - Part 3: Solderless accessible insulation displacement connections; general requirements, test methods and practical guidance (IEC 60352-3:1993); German version EN 60352-3:1994 |
| CEI EN 61076-4-105 : 2001 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION= AND AUDIO INDUSTRY |
| IEC 60807-1:1991 | Rectangular connectors for frequencies below 3 MHz - Part 1:Generic specification - General requirements and guide for thepreparation of detail specifications for connectors with assessedquality |
| I.S. EN 175101-809:2004 | DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2.54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75101-801, WITH ASSESSED QUALITY |
| IEC 62847:2016 | Railway applications - Rolling stock - Electrical connectors - Requirements and test methods |
| IEC 60603-11:1992 | Connectors for frequencies below 3 MHz for use with printed boards - Part 11: Detail specification for concentric connectors (dimensions for free connectors and fixed connectors) |
| IEC 61076-4-104:1999 | Connectors for use in d.c., low frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| IEC 60603-2:1995 | Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features |
| EN 60603-2:1998/A1:2005 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| EN 60352-6:1997 | Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance |
| EN 175101-802:1999 | Detail specification: Two-part connectors for printed boards for high number of contacts with basic grid of 2,54 mm on 3 or 4 rows |
| EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| EN 60352-1:1997 | Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
| EN 60603-1:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 1: Generic specification - General requirements and guide for the preparation of detail specifications, with assessed quality |
| EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 61076-4-104:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.