IEC 60131-1:1984
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Lever switches. Part 1: General requirements and rules for the preparation of detail specifications
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
23-07-2013
English - French
01-01-1984
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
PREFACE
SECTION ONE - GENERAL
1 Scope
2 Object
3 Terminology
4 Classification into climatic categories
5 Creepage and clearance distances
6 Voltage and current ratings
7 Marking
8 IEC type designation
SECTION TWO - GENERAL REQUIREMENTS, TESTS AND TEST SCHEDULES
9 Workmanship
10 Testing
SECTION THREE - RULES FOR THE PREPARATION OF DETAIL
SPECIFICATIONS
11 Titles of detail specifications
12 Drawing information
13 Contents of detail specification
Applies to lever switches for use in electronic and electromechanical equipment, including switches necessary to connect the supply mains. Switches covered by this standard have a maximum rated voltage not exceeding 500 V and a maximum rated current not exceeding 25 A (d.c. or a.c. r.m.s. values).Establishes uniform specifications and type test requirements for lever switches also establish rules for the preparation of detail specifications.
| Committee |
TC 23/SC 23J
|
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| NEN 10131-1 : 1985 | Identical |
| BS 9561:1979 | Similar to |
| CEI 48-1 : 2ED 1997 | Identical |
| IEC 60512-8:1993 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60512-6:1984 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| IEC 60512-7:1993 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests |
| IEC 60512-4:1976 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 4: Dynamic stress tests |
| IEC 60512-9:1992 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 9: Miscellaneous tests |
| ISO 129:1985 | Technical drawings Dimensioning General principles, definitions, methods of execution and special indications |
| IEC 60512-5:1992 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests |
| IEC 60512-1:2001 | Connectors for electronic equipment - Tests and measurements - Part 1: General |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
| ISO/R 286:1962 | ISO system of limits and fits Part I : General, tolerances and deviations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.