I.S. EN ISO 80601-2-13:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MEDICAL ELECTRICAL EQUIPMENT - PART 2-13: PARTICULAR REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE OF AN ANAESTHETIC WORKSTATION (ISO 80601-2-13:2011)
Hardcopy , PDF
17-12-2019
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
201.1 Scope, object and related standards
201.2 Normative references
201.3 Terms and definitions
201.4 General requirements
201.5 General requirements for testing ME EQUIPMENT
201.6 Classification of ME EQUIPMENT and ME SYSTEMS
201.7 ME EQUIPMENT identification, marking and documents
201.8 Protection against electrical HAZARDS from ME EQUIPMENT
201.9 Protection against mechanical HAZARDS of ME EQUIPMENT
and ME SYSTEMS
201.10 Protection against unwanted and excessive radiation
HAZARDS
201.11 Protection against excessive temperatures and other
HAZARDS
201.12 Accuracy of controls and instruments and protection
against hazardous outputs
201.13 HAZARDOUS SITUATIONS and fault conditions
201.14 PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS)
201.15 Construction of ME EQUIPMENT
201.16 ME SYSTEMS
201.17 Electromagnetic compatibility of ME EQUIPMENT AND ME
SYSTEMS
201.101 Additional requirements for ANAESTHETIC GAS DELIVERY
SYSTEMS
201.102 Additional requirements for an ANAESTHETIC BREATHING
SYSTEM
201.103 Additional requirements for an ANAESTHETIC GAS
SCAVENGING SYSTEM
201.104 Additional requirements for an ANAESTHETIC VAPOUR
DELIVERY SYSTEM
201.105 Additional requirements for an ANAESTHETIC VENTILATOR
pause
201.106 Display loops
201.107 Clinical evaluation
202 Electromagnetic compatibility - Requirements and tests
203 General requirements for radiation protection in
diagnostic X-ray equipment
206 Usability
208 General requirements, tests and guidance for ALARM
SYSTEMS in MEDICAL ELECTRICAL EQUIPMENT and MEDICAL
ELECTRICAL SYSTEMS
209 Requirements for environmentally conscious design
210 PROCESS requirements for the development of physiologic
closed-loop controllers
211 Requirements for MEDICAL ELECTRICAL EQUIPMENT and MEDICAL
ELECTRICAL SYSTEMS used in the home healthcare
Annex C (informative) - Guide to marking and labelling
requirements for ME EQUIPMENT and ME SYSTEMS or their
parts
Annex D (informative) - Symbols on marking
Annex AA (informative) - Particular guidance and rationale
Annex BB (normative) - Test for flammability of anaesthetic
agent
Annex CC (informative) - Environmental aspects
Annex DD (informative) - Reference to the essential principles
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 93/42/EEC
Bibliography
Alphabetized index of defined terms used in this particular
standard
Pertains to the BASIC SAFETY and ESSENTIAL PERFORMANCE of an ANAESTHETIC WORKSTATION for administering inhalational anaesthesia whilst continuously attended by a professional OPERATOR.
| DevelopmentNote |
Supersedes I.S. EN ISO 8835-2, I.S. EN ISO 8835-3, I.S. EN ISO 8835-4, I.S. EN ISO 8835-5 & I.S. EN 60601-2-13. (02/2013)
|
| DocumentType |
Standard
|
| Pages |
119
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 80601-2-13:2011 | Identical |
| EN ISO 80601-2-13:2012 | Identical |
| ISO 8836:2014 | Suction catheters for use in the respiratory tract |
| ISO 5360:2016 | Anaesthetic vaporizers Agent-specific filling systems |
| EN 15986:2011 | Symbol for use in the labelling of medical devices - Requirements for labelling of medical devices containing phthalates |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
| IEC 60601-1-6:2010+AMD1:2013 CSV | Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: Usability |
| BS 4272-3:1989 | Anaesthetic and analgesic machines Specification for continuous flow anaesthetic machines |
| ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
| ISO 5356-1:2015 | Anaesthetic and respiratory equipment Conical connectors Part 1: Cones and sockets |
| ISO 9170-2:2008 | Terminal units for medical gas pipeline systems — Part 2: Terminal units for anaesthetic gas scavenging systems |
| ISO 10651-4:2002 | Lung ventilators — Part 4: Particular requirements for operator-powered resuscitators |
| IEC 60601-1-10:2007+AMD1:2013 CSV | Medical electrical equipment - Part 1-10: General requirements forbasic safety and essential performance - Collateral Standard: Requirements for the development of physiologic closed-loopcontrollers |
| ISO 8835-7:2011 | Inhalational anaesthesia systems — Part 7: Anaesthetic systems for use in areas with limited logistical supplies of electricity and anaesthetic gases |
| ISO/TR 14969:2004 | Medical devices Quality management systems Guidance on the application of ISO 13485: 2003 |
| IEC 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| IEC 60601-1-8:2006+AMD1:2012 CSV | Medical electrical equipment - Part 1-8: General requirements forbasic safety and essential performance - Collateral Standard: General requirements, tests and guidance for alarm systems inmedical electrical equipment and medical electrical systems |
| ISO 7396-2:2007 | Medical gas pipeline systems Part 2: Anaesthetic gas scavenging disposal systems |
| ISO 5145:2014 | Cylinder valve outlets for gases and gas mixtures Selection and dimensioning |
| ISO 5356-2:2012 | Anaesthetic and respiratory equipment — Conical connectors — Part 2: Screw-threaded weight-bearing connectors |
| ISO 10079-1:2015 | Medical suction equipment Part 1: Electrically powered suction equipment |
| ISO 5367:2014 | Anaesthetic and respiratory equipment — Breathing sets and connectors |
| IEC 60601-1-2:2014 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
| ISO 5359:2014 | Anaesthetic and respiratory equipment — Low-pressure hose assemblies for use with medical gases |
| ISO 5362:2006 | Anaesthetic reservoir bags |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| ISO 8185:2007 | Respiratory tract humidifiers for medical use Particular requirements for respiratory humidification systems |
| ISO/TR 16142:2006 | Medical devices Guidance on the selection of standards in support of recognized essential principles of safety and performance of medical devices |
| IEC 62304:2006+AMD1:2015 CSV | Medical device software - Software life cycle processes |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ASTM F 2761 : 2009 : R2013 | Medical Devices and Medical Systems - Essential safety requirements for equipment comprising the patient-centric integrated clinical environment (ICE) - Part 1: General requirements and conceptual model |
| IEC 60601-1-3:2008+AMD1:2013 CSV | Medical electrical equipment - Part 1-3: General requirements forbasic safety and essential performance - Collateral Standard: Radiation protection in diagnostic X-ray equipment |
| ISO 2878:2017 | Rubber, vulcanized or thermoplastic Antistatic and conductive products Determination of electrical resistance |
| ISO 80601-2-55:2011 | Medical electrical equipment Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors |
| ISO 10079-3:2014 | Medical suction equipment Part 3: Suction equipment powered from a vacuum or positive pressure gas source |
| ISO 407:2004 | Small medical gas cylinders Pin-index yoke-type valve connections |
| ISO 5358:1992 | Anaesthetic machines for use with humans |
| ISO 14155:2011 | Clinical investigation of medical devices for human subjects Good clinical practice |
| ISO 9170-1:2017 | Terminal units for medical gas pipeline systems — Part 1: Terminal units for use with compressed medical gases and vacuum |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| ISO 4135:2001 | Anaesthetic and respiratory equipment Vocabulary |
| ISO 10524-1:2006 | Pressure regulators for use with medical gases Part 1: Pressure regulators and pressure regulators with flow-metering devices |
| ISO 594-2:1998 | Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment Part 2: Lock fittings |
| ISO 15223-1:2016 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements |
| IEC 60601-1-9:2007+AMD1:2013 CSV | Medical electrical equipment - Part 1-9: General requirements forbasic safety and essential performance - Collateral Standard: Requirements for environmentally conscious design |
| IEC 60601-1-4:1996+AMD1:1999 CSV | Medical electrical equipment - Part 1-4: General requirements for safety - Collateral Standard: Programmable electrical medical systems |
| ISO 7396-1:2016 | Medical gas pipeline systems — Part 1: Pipeline systems for compressed medical gases and vacuum |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.