I.S. EN ISO 3269:2000
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
FASTENERS - ACCEPTANCE INSPECTION
Hardcopy , PDF
31-03-2020
English
01-01-2000
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
characteristics
Annex A (informative) Recommendations for
acceptance-inspection procedures (for example,
for dimensional characteristics)
Annex B (informative) Guidance and explanation
concerning the principle of this International
Standard
Bibliography
Describes the acceptance inspection procedure that the purchaser of fasteners must follow in order to determine whether a lot of fasteners will be accepted or rejected in cases where no other such procedure was agreed with the supplier at the time the fasteners were ordered. It is applicable to bolts, screws, studs, nuts, pins, washers, blind rivets and other related fasteners not intended for high volume machine assembly, special-purpose applications or specially engineered applications requiring greater in-process control and lot traceability.
DocumentType |
Standard
|
Pages |
30
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Withdrawn
|
SupersededBy |
Standards | Relationship |
ISO 3269:2000 | Identical |
BS EN ISO 3269:2001 | Identical |
NEN EN ISO 3269 : 2000 | Identical |
NS EN ISO 3269 : 1ED 2000 | Identical |
EN ISO 3269:2000 | Identical |
NF EN ISO 3269 : 2000 | Identical |
UNI EN ISO 3269 : 2002 | Identical |
SN EN ISO 3269 : 2000 | Identical |
NBN EN ISO 3269 : 2000 | Identical |
DIN EN ISO 3269:2000-11 | Identical |
ONORM EN ISO 3269 : 2000 | Identical |
ISO 8839:1986 | Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals |
ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
ISO 10683:2014 | Fasteners Non-electrolytically applied zinc flake coatings |
EN 26157-3:1991 | Fasteners - Surface discontinuities - Part 3: Bolts, screws and studs for special requirements (ISO 6157-3:1988) |
ISO 4759-3:2016 | Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F |
ISO 4042:1999 | Fasteners Electroplated coatings |
ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
ISO 6157-3:1988 | Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements |
EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
EN 26157-1:1991 | Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements (ISO 6157-1:1988) |
ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
EN ISO 4759-3:2016 | Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016) |
ISO 7085:1999 | Mechanical and performance requirements of case hardened and tempered metric thread rolling screws |
ISO 8402:1994 | Quality management and quality assurance — Vocabulary |
EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
ISO 1502:1996 | ISO general-purpose metric screw threads Gauges and gauging |
ISO 898-6:1994 | Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread |
ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread |
ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
EN ISO 2702:2011 | Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011) |
ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
EN ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012) |
EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
EN ISO 898-6:1995 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994) |
ISO 8992:2005 | Fasteners — General requirements for bolts, screws, studs and nuts |
EN ISO 7085 : 1999 | MECHANICAL AND PERFORMANCE REQUIREMENTS OF CASE HARDENED AND TEMPERED METRIC THREAD ROLLING SCREWS |
ISO 2702:2011 | Heat-treated steel tapping screws — Mechanical properties |
ISO 1478:1999 | Tapping screws thread |
EN 28839:1991 | Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986) |
EN ISO 1478:1999 | Tapping screws thread (ISO 1478:1999) |
ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.