I.S. EN ISO 28765:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
VITREOUS AND PORCELAIN ENAMELS - DESIGN OF BOLTED STEEL TANKS FOR THE STORAGE OR TREATMENT OF WATER OR MUNICIPAL OR INDUSTRIAL EFFLUENTS AND SLUDGES (ISO 28765:2016)
Hardcopy , PDF
14-06-2023
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Units
6 Information and requirements to be agreed and documented
7 Applicable standards
8 Loads
9 Design
10 Vitreous-enamel coating
11 Installation
12 Disinfection
Bibliography
Specifies the requirements for the design and use of vitreous-enamel-coated bolted cylindrical steel tanks for the storage or treatment of water or municipal or industrial effluents and sludges.
| DevelopmentNote |
Supersedes I.S. EN 15282. (04/2011)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 28765:2016 | Identical |
| ISO 28765:2016 | Identical |
| ANSI/AWWA D103 : 2009 | FACTORY-COATED BOLTED CARBON STEEL TANKS FOR WATER STORAGE |
| ISO 28706-2:2017 | Vitreous and porcelain enamels — Determination of resistance to chemical corrosion — Part 2: Determination of resistance to chemical corrosion by boiling acids, boiling neutral liquids, alkaline liquids and/or their vapours |
| EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
| ISO 2746:2015 | Vitreous and porcelain enamels High voltage test |
| ISO 28763:2008 | Vitreous and porcelain enamels Regenerative, enamelled and packed panels for air-gas and gas-gas heat exchangers Specifications |
| BS 7793-1:1995 | Vitreous enamel coatings for use on bolted steel panels Specification for coatings on bolted steel panels for use in agricultural slurry tanks |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| BS 5502-50(1993) : 1993 | BUILDINGS AND STRUCTURES FOR AGRICULTURE - PART 50: CODE OF PRACTICE FOR DESIGN, CONSTRUCTION AND USE OF STORAGE TANKS AND RECEPTION PITS FOR LIVESTOCK SLURRY |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| BS 5395-3:1985 | Stairs, ladders and walkways Code of practice for the design of industrial type stairs, permanent ladders and walkways |
| ISO 4532:1991 | Vitreous and porcelain enamels Determination of the resistance of enamelled articles to impact Pistol test |
| ISO 28706-1:2008 | Vitreous and porcelain enamels — Determination of resistance to chemical corrosion — Part 1: Determination of resistance to chemical corrosion by acids at room temperature |
| ISO 4528:2015 | Vitreous and porcelain enamel finishes Guide to selection of test methods for vitreous and porcelain enamelled areas of articles |
| ISO 6370-2:2011 | Vitreous and porcelain enamels Determination of the resistance to abrasion Part 2: Loss in mass after sub-surface abrasion |
| ISO 15686-1:2011 | Buildings and constructed assets — Service life planning — Part 1: General principles and framework |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
| ISO 8289:2000 | Vitreous and porcelain enamels Low voltage test for detecting and locating defects |
| BS 7793-2:1996 | Vitreous enamel coatings for use on bolted steel panels Specification for coatings on bolted steel panels for use in industrial liquid storage tanks |
| ISO 28706-3:2008 | Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 3: Determination of resistance to chemical corrosion by alkaline liquids using a hexagonal vessel |
| EN 15771:2010 | Vitreous and porcelain enamels - Determination of surface scratch hardness according to the Mohs scale |
| ISO 28706-4:2016 | Vitreous and porcelain enamels — Determination of resistance to chemical corrosion — Part 4: Determination of resistance to chemical corrosion by alkaline liquids using a cylindrical vessel |
| BS 5502-22(2003) : 2003 | BUILDINGS AND STRUCTURES FOR AGRICULTURE - PART 22: CODE OF PRACTICE FOR DESIGN, CONSTRUCTION AND LOADING |
| BS 7885:1997 | Code of practice for safe entry into silos |
| EN 1998-4:2006 | Eurocode 8 - Design of structures for earthquake resistance - Part 4: Silos, tanks and pipelines |
| EN 10209:2013 | Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.