I.S. EN ISO 15877-2:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 2: PIPES
Hardcopy , PDF
02-02-2021
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Material
4.1 General
4.2 Pipe material
4.3 Evaluation of sigma[LPL]-values
4.4 Influence on water intended for human consumption
5 General characteristics
5.1 Appearance
5.2 Chamfering
5.3 Opacity
6 Geometrical
6.1 General
6.2 Dimensions of pipes
6.3 Wall thicknesses and their tolerances
7 Mechanical characteristics
7.1 Resistance to internal pressure
7.2 Impact resistance
7.3 Tensile strength
8 Physical characteristics
9 Performance requirements
10 Adhesives
11 Marking
11.1 General
11.2 Minimum required marking
11.3 Additional marking
Annex A (informative) Derivation of the maximum
calculated pipe value, S[calc,max]
Bibliography
Describes the requirements of pipes made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application.
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NEN EN ISO 15877-2 : 2009 AMD 1 2010 | Identical |
NF EN ISO 15877-2 : 2009 AMD 1 2011 | Identical |
UNI EN ISO 15877-2 : 2011 | Identical |
UNE-EN ISO 15877-2:2009 | Identical |
NBN EN ISO 15877-2 : 2009 AMD 1 2010 | Identical |
SN EN ISO 15877-2 : 2009 AMD 1 2011 | Identical |
ISO 15877-2:2009 | Identical |
NS EN ISO 15877-2 : 2009 AMD 1 2010 | Identical |
DIN EN ISO 15877-2:2011-03 | Identical |
BS EN ISO 15877-2 : 2009 | Identical |
ONORM EN ISO 15877-2 : 2011 | Identical |
ISO 6259-2:1997 | Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) |
ISO 15877-3:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 3: Fittings |
ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
ISO 15877-1:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 1: General |
ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
ISO 15877-5:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 5: Fitness for purpose of the system |
ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
ISO/TS 15877-7:2009 | Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 7: Guidance for the assessment of conformity |
EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.