I.S. EN ISO 15875-2:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES
Hardcopy , PDF
18-01-2021
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material
4.1 Pipe material
4.2 Evaluation of sigma[LCL]-values
4.3 Influence on water intended for human consumption
5 General characteristics
5.1 Appearance
5.2 Opacity
6 Geometrical characteristics
6.1 General
6.2 Dimensions of pipes
7 Mechanical characteristics
8 Physical and chemical characteristics
9 Performance requirements
10 Marking
10.1 General requirements
10.2 Minimum required marking
Annex A (informative) Derivation of S[calc,max] values
A.1 General
A.2 Design stress
A.3 Derivation of maximum value of S[calc] (S[calc,max])
A.4 Use of S[calc,max] to determine wall thickness
Bibliography
Specifies the characteristics of pipes made from crosslinked polyethylene (PE-X) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, and for heating systems, under design pressures and temperatures according to the class of application.
DocumentType |
Standard
|
Pages |
52
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
ISO 15875-2:2003 | Identical |
NBN EN ISO 15875-2 : 2004 AMD 1 2007 | Identical |
NS EN ISO 15875-2 : 2003 AMD 1 2007 | Identical |
SN EN ISO 15875-2 : 2004 AMD 1 2007 | Identical |
NEN EN ISO 15875-2 : 2004 AMD 1 2007 | Identical |
UNE-EN ISO 15875-2:2004 | Identical |
UNI EN ISO 15875-2 : 2008 | Identical |
BS EN ISO 15875-2:2003 | Identical |
ONORM EN ISO 15875-2 : 2008 | Identical |
EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
EN ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003) |
ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system |
ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2003) |
EN 743 : 1994 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF THE LONGITUDINAL REVERSION |
ISO 21003-5:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system |
EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
EN 578 : 1993 | PLASTICS PIPING SYSTEMS - PLASTICS PIPES AND FITTINGS - DETERMINATION OF THE OPACITY |
ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
EN ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998) |
EN ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003) |
ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
EN 579:1993 | Plastics piping systems - Crosslinked polyethylene (PE-X) pipes - Determination of degree of crosslinking by solvent extraction |
ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
ISO 21003-1:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General |
ISO 15875-1:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General |
ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings |
ISO 21003-3:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 3: Fittings |
ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.