I.S. EN ISO 15494:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM (ISO 15494:2015)
Hardcopy , PDF
01-12-2018
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material
6 General characteristics
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Chemical characteristics
11 Electrical characteristics
12 Performance requirements
13 Classification of components
14 Design and installation
15 Declaration of conformity
16 Marking
Annex A (normative) - Specific characteristics and
requirements for industrial piping systems
made from polybutene (PB)
Annex B (normative) - Specific characteristics and
requirements for industrial piping systems
made from polyethylene (PE)
Annex C (normative) - Specific characteristics and
requirements for industrial piping systems
made from polyethylene of raised temperature
resistance (PE-RT)
Annex D (normative) - Specific characteristics and
requirements for industrial piping systems
made from crosslinked polyethylene (PE-X)
Annex E (normative) - Specific characteristics and
requirements for industrial piping systems
made from polypropylene (PP)
Annex F (informative) - Design and installation
Bibliography
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive for pressure
equipment 97/23/EC
Defines the characteristics and requirements for components such as pipes, fittings, and valves made from one of the following materials intended to be used for thermoplastics piping systems in the field of industrial applications above and below ground: - polybutene (PB); - polyethylene (PE); - polyethylene of raised temperature resistance (PE-RT); - crosslinked polyethylene (PE-X); and - polypropylene (PP).
| DocumentType |
Standard
|
| Pages |
118
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN ISO 15494 : 2003 | Identical |
| EN ISO 15494:2015 | Identical |
| NBN EN ISO 15494 : 2015 | Identical |
| DIN EN ISO 15494:2016-03 | Identical |
| ISO 15494:2015 | Identical |
| NEN EN ISO 15494 : 2015 | Identical |
| SN EN ISO 15494 : 2016 | Identical |
| UNE-EN ISO 15494:2016 | Identical |
| NF EN ISO 15494 : 2015 | Identical |
| BS EN ISO 15494:2015 | Identical |
| UNI EN ISO 15494 : 2005 | Identical |
| ONORM EN ISO 15494 : 2016 | Identical |
| ISO 16135:2006 | Industrial valves Ball valves of thermoplastics materials |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| ISO 3213:2009 | Polypropylene (PP) pipes Effect of time and temperature on the expected strength |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 265-1:1988 | Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 10146:1997 | Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength |
| ISO 4427-1:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| ISO 14531-1:2002 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 1: Pipes |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4433-1:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| ISO 18553:2002 | Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| ISO 12230:2012 | Polybutene-1 (PB-1) pipes — Effect of time and temperature on the expected strength |
| CEN/TR 15438:2007 | Plastics piping systems - Guidance for coding of products and their intended uses |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 15853:1999 | Thermoplastics materials Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| HD 60364-1:2008/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 1: FUNDAMENTAL PRINCIPLES, ASSESSMENT OF GENERAL CHARACTERISTICS, DEFINITIONS |
| ISO 16871:2003 | Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
| ISO 472:2013 | Plastics — Vocabulary |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 4433-2:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| ISO 24033:2009 | Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength |
| ISO 17885:2015 | Plastics piping systems Mechanical fittings for pressure piping systems Specifications |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 16138:2006 | Industrial valves Diaphragm valves of thermoplastics materials |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 16137:2006 | Industrial valves Check valves of thermoplastics materials |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 16136:2006 | Industrial valves Butterfly valves of thermoplastics materials |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 16139:2006 | Industrial valves Gate valves of thermoplastics materials |
| ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
| ISO 10147:2011 | Pipes and fittings made of crosslinked polyethylene (PE-X) Estimation of the degree of crosslinking by determination of the gel content |
| ISO 760:1978 | Determination of water Karl Fischer method (General method) |
| ISO 21787:2006 | Industrial valves Globe valves of thermoplastics materials |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 712:1993 | Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.