I.S. EN ISO 13408-1:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ASEPTIC PROCESSING OF HEALTH CARE PRODUCTS - PART 1: GENERAL REQUIREMENTS (ISO 13408-1:2008, INCLUDING AMD 1:2013)
Hardcopy , PDF
02-05-2024
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and defini
4 Quality system elements
5 Aseptic process definition
6 Manufacturing environment
7 Equipment
8 Personnel
9 Manufacture of the product
10 Process simulat
11 Test for sterility
Annex A (informative) - Example of a flow chart
Annex B (informative) - Typical elements of an aseptic
process definition
Annex C (informative) - Examples of specific risks
Annex D (informative) - Comparison of classification of
cleanrooms
Annex E (informative) - Specification for water used
in the process
Annex F (informative) - Aseptic processing area
Bibliography
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 90/385/EEC on active implantable
medical devices
Annex ZB (informative) - Relationship between this
European Standard and the Essential Requirements of
EU Directive 93/42/EEC on medical devices
Annex ZC (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 98/79/EC on in vitro diagnostic
medical devices
Describes the general requirements for, and offers guidance on, processes, programmes and procedures for development, validation and routine control of the manufacturing process for aseptically-processed health care products.
| DevelopmentNote |
Supersedes I.S. EN 13824. (07/2011)
|
| DocumentType |
Standard
|
| Pages |
66
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 13408-1:2008 | Identical |
| EN ISO 13408-1:2015 | Identical |
| ISO 13408-4:2005 | Aseptic processing of health care products — Part 4: Clean-in-place technologies |
| EN ISO 14644-4:2001 | Cleanrooms and associated controlled environments - Part 4: Design, construction and start-up (ISO 14644-4:2001) |
| ISO 11137-1:2006 | Sterilization of health care products Radiation Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| EN ISO 14698-1:2003 | Cleanrooms and associated controlled environments - Biocontamination control - Part 1: General principles and methods (ISO 14698-1:2003) |
| EN ISO 14937:2009 | Sterilization of health care products - General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices (ISO 14937:2009) |
| ISO 14160:2011 | Sterilization of health care products Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives Requirements for characterization, development, validation and routine control of a sterilization process for medical devices |
| ISO 14698-2:2003 | Cleanrooms and associated controlled environments Biocontamination control Part 2: Evaluation and interpretation of biocontamination data |
| EN ISO 13408-3:2011 | Aseptic processing of health care products - Part 3: Lyophilization (ISO 13408-3:2006) |
| EN ISO 13408-4:2011 | Aseptic processing of health care products - Part 4: Clean-in-place technologies (ISO 13408-4:2005) |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| EN 556-2:2015 | Sterilization of medical devices - Requirements for medical devices to be designated 'STERILE" - Part 2: Requirements for aseptically processed medical devices |
| EN ISO 13408-5:2011 | Aseptic processing of health care products - Part 5: Sterilization in place (ISO 13408-5:2006) |
| ISO 14644-2:2015 | Cleanrooms and associated controlled environments Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration |
| ISO 13408-2:2003 | Aseptic processing of health care products Part 2: Filtration |
| ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
| ISO 14644-5:2004 | Cleanrooms and associated controlled environments — Part 5: Operations |
| ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO/TR 14969:2004 | Medical devices Quality management systems Guidance on the application of ISO 13485: 2003 |
| EN ISO 11135:2014 | Sterilization of health-care products - Ethylene oxide - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 11135:2014) |
| ISO 11135-1:2007 | Sterilization of health care products Ethylene oxide Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 13408-3:2006 | Aseptic processing of health care products Part 3: Lyophilization |
| ISO 14698-1:2003 | Cleanrooms and associated controlled environments Biocontamination control Part 1: General principles and methods |
| EN ISO 11137-2:2015 | Sterilization of health care products - Radiation - Part 2: Establishing the sterilization dose (ISO 11137-2:2013) |
| ISO 14644-3:2005 | Cleanrooms and associated controlled environments Part 3: Test methods |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 9004:2009 | Managing for the sustained success of an organization A quality management approach |
| ISO/TS 11139:2006 | Sterilization of health care products Vocabulary |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| ISO 11137-2:2013 | Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose |
| EN ISO 14644-5:2004 | Cleanrooms and associated controlled environments - Part 5: Operations (ISO 14644-5:2004) |
| ISO 14644-7:2004 | Cleanrooms and associated controlled environments — Part 7: Separative devices (clean air hoods, gloveboxes, isolators and mini-environments) |
| ISO 14644-1:2015 | Cleanrooms and associated controlled environments Part 1: Classification of air cleanliness by particle concentration |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 11137-1:2015 | Sterilization of health care products - Radiation - Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 11137-1:2006, including Amd 1:2013) |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 14644-4:2001 | Cleanrooms and associated controlled environments — Part 4: Design, construction and start-up |
| EN 1822-1:2009 | High efficiency air filters (EPA, HEPA and ULPA) - Part 1: Classification, performance testing, marking |
| EN ISO 17665-1:2006 | Sterilization of health care products - Moist heat - Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 17665-1:2006) |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| EN ISO 14644-2:2015 | Cleanrooms and associated controlled environments - Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration (ISO 14644-2:2015) |
| EN ISO 14644-7:2004 | Cleanrooms and associated controlled environments - Part 7: Separative devices (clean air hoods, gloveboxes, isolators and mini-environments) (ISO 14644-7:2004) |
| EN ISO 20857:2013 | Sterilization of health care products - Dry heat - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 20857:2010) |
| ISO 13408-6:2005 | Aseptic processing of health care products Part 6: Isolator systems |
| EN ISO 14644-1:2015 | Cleanrooms and associated controlled environments - Part 1: Classification of air cleanliness by particle concentration (ISO 14644-1:2015) |
| EN ISO 14160:2011 | Sterilization of health care products - Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives - Requirements for characterization, development, validation and routine control of a sterilization process for medical devices (ISO 14160:2011) |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
| ISO 13408-5:2006 | Aseptic processing of health care products Part 5: Sterilization in place |
| EN ISO 14644-3:2005 | Cleanrooms and associated controlled environments - Part 3: Test methods (ISO 14644-3:2005) |
| ISO 15223:2000 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.