I.S. EN ISO 11960:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPES FOR USE AS CASING OR TUBING FOR WELLS (ISO 11960:2014)
Hardcopy , PDF
31-05-2021
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Conformance
3 Normative references
4 Terms, definitions, symbols and abbreviated terms
5 Information to be supplied by the purchaser
6 Process of manufacture
7 Material requirements
8 Dimensions, masses, tolerances, product ends
and defects
9 Couplings
10 Inspection and testing
11 Marking
12 Coating and protection
13 Documents
14 Minimum facility requirements for various
categories of manufacturer
Annex A (normative) - Supplementary requirements
Annex B (normative) - Purchaser inspection
Annex C (normative) - Tables in SI units
Annex D (normative) - Figures in SI (USC) units
Annex E (normative) - Tables in USC units
Annex F (normative) - Use of the API Monogram by
Licensees
Annex G (informative) - Procedures used to convert
from USC units to SI units
Annex H (normative) - Product Specification Levels
Annex I (normative) - Requirements for thread protector
design validation
Annex J (informative) - Summary of Product Specification
Level (PSL) requirements
Annex K (normative) - Modification of the hydrogen sulfide
titration procedures in ANSI-NACE TM0284-2003,
Appendix C
Annex L (informative) - Technical changes from the previous
edition
Bibliography
Describes the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material and establishes requirements for three product specification levels (PSL-1, PSL-2, PSL-3).
| DocumentType |
Standard
|
| Pages |
280
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN ISO 11960 : 2014 | Identical |
| BS EN ISO 11960:2014 | Identical |
| ISO 11960:2014 | Identical |
| NBN EN ISO 11960 : 2014 | Identical |
| UNI EN ISO 11960 : 2014 | Identical |
| DIN EN ISO 11960:2014-05 | Identical |
| NEN EN ISO 11960 : 2014 | Identical |
| NF EN ISO 11960 : 2015 | Identical |
| SN EN ISO 11960 : 2014 | Identical |
| EN ISO 11960:2014 | Identical |
| ONORM EN ISO 11960 : 2014 | Identical |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| API 5T1 : 2017 | IMPERFECTION AND DEFECT TERMINOLOGY |
| ISO 10893-3:2011 | Non-destructive testing of steel tubes Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections |
| ISO 10893-5:2011 | Non-destructive testing of steel tubes Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ASTM E 309 : 2016 : REDLINE | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation |
| ISO/TR 9769:1991 | Steel and iron Review of available methods of analysis |
| API 5CT : 2012 | CASING AND TUBING |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| NACE TM 02 84 : 2016 | EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ASTM E 273 : 2015 : REDLINE | Standard Practice for Ultrasonic Testing of the Weld Zone of Welded Pipe and Tubing |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
| ISO 10893-11:2011 | Non-destructive testing of steel tubes Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| API 5A2 : 6ED 88 | BULLETIN ON THREAD COMPOUNDS FOR CASING, TUBING AND LINE PIPE |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| ISO/IEC 17011:2004 | Conformity assessment General requirements for accreditation bodies accrediting conformity assessment bodies |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 6508-2:2015 | Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines and indenters |
| ISO 15156-2:2015 | Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons |
| ISO 13678:2010 | Petroleum and natural gas industries Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements |
| API Q1 : 2013 | SPECIFICATION FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS FOR MANUFACTURING ORGANIZATIONS FOR THE PETROLEUM AND NATURAL GAS INDUSTRY |
| API 5A3 : 2011 | RECOMMENDED PRACTICE ON THREAD COMPOUNDS FOR CASING, TUBING, LINE PIPE, AND DRILL STEM ELEMENTS |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| ISO 11484:2009 | Steel products — Employer's qualification system for non-destructive testing (NDT) personnel |
| ISO 6506-2:2017 | Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines |
| ISO/TR 10400:2007 | Petroleum and natural gas industries Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ISO 10893-2:2011 | Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| API TR 5C3 : 2008 | CALCULATING PERFORMANCE PROPERTIES OF PIPE USED AS CASING OR TUBING |
| ISO 10893-10:2011 | Non-destructive testing of steel tubes Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.