I.S. EN ISO 11298-2:2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11298-2:2018)
Hardcopy , PDF
04-03-2018
29-01-2020
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the system for
pipes and fittings at the 'I' stage
9 Installation practice
Annex A (normative) - Layered pipes
Bibliography
Describes requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks.
| Committee |
TC 138
|
| DocumentType |
Test Method
|
| Pages |
26
|
| ProductNote |
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 11298-2:2018 | Identical |
| EN ISO 11298-2:2018 | Identical |
| ISO 4427-3:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings |
| ISO 4427-1:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 4427-5:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| ISO 11298-1:2010 | Plastics piping systems for renovation of underground water supply networks — Part 1: General |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| ISO 4427-2:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.