I.S. EN ISO 11297-3:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
Hardcopy , PDF
28-11-2018
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the "M" stage
6 Fittings at the "M" stage
7 Ancillary components
8 Fitness for purpose of the installed lining
system at the "I" stage
9 Installation practice
Annex A (normative) - Factory-folded heat-reverted
polyethylene (PE) pipe - Determination of
memory ability
Bibliography
Describes requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.
| DocumentType |
Standard
|
| Pages |
29
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 11297-3:2013 | Identical |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) |
| ISO 4427-1:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4427-5:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| ISO 11297-1:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Part 1: General |
| ISO 4427-2:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.