I.S. EN 62137-1-1:2007
Current
The latest, up-to-date edition.
SURFACE MOUNTING TECHNOLOGY - ENVIRONMENTAL AND ENDURANCE TEST METHODS FOR SURFACE MOUNT SOLDER JOINT - PART 1-1: PULL STRENGTH TEST
Hardcopy , PDF
English
01-01-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General remarks
5 Test equipment and materials
5.1 Flow soldering equipment
5.2 Reflow soldering equipment
5.3 Pull strength test equipment
5.4 Optical microscope
5.5 Test substrate
5.6 Solder alloy
5.7 Flux for flow soldering
5.8 Solder paste
6 Mounting method
6.1 Flow soldering
6.2 Reflow soldering
7 Test conditions
7.1 Test: Rapid change of temperature
7.2 Pull strength test
8 Test procedure
8.1 Test sequence
8.2 Pre-conditioning
8.3 Initial pull strength measurement
8.4 Rapid change of temperature
8.5 Recovery
8.6 Intermediate/final pull strength measurement
9 Items to be included in the test report
10 Items to be given in the product specification
Annex A (normative) - Pull strength test - Details
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
Applies to gull-wing lead surface mounting components. The method is designed to test and evaluate the endurance of the solder joint between component leads and lands on a substrate, by means of a pull type mechanical stress.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NF EN 62137-1-1 : 2014 | Identical |
| EN 62137-1-1 : 2007 | Identical |
| DIN EN 62137-1-1:2008-02 | Identical |
| IEC 62137-1-1:2007 | Identical |
| BS EN 62137-1-1:2007 | Identical |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 61190-1-2:2014 | Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly |
| EN 61190-1-1:2002 | Attachment materials for electronic assembly - Part 1-1: Requirements for soldering fluxes for high-quality interconnections in electronics assembly |
| IEC 61249-2-7:2002 | Materials for printed boards and other interconnecting structures - Part 2-7: Reinforced base materials clad and unclad - Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 61249-2-7:2002/corrigendum:2005 | MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-7: REINFORCED BASE MATERIALS CLAD AND UNCLAD - EPOXIDE WOVEN E-GLASS LAMINATED SHEET OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD |
| IEC 61190-1-1:2002 | Attachment materials for electronic assembly - Part 1-1: Requirements for soldering fluxes for high-quality interconnections in electronics assembly |
| IEC 60194:2015 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 61188-5-5:2007 | Printed boards and printed board assemblies - Design and use - Part 5-5: Attachment (land/joint) considerations - Components with gull-wing leads on four sides |
| EN 61190-1-3:2007/A1:2010 | ATTACHMENT MATERIALS FOR ELECTRONIC ASSEMBLY - PART 1-3: REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDER FOR ELECTRONIC SOLDERING APPLICATIONS |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 61190-1-2:2014 | Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 60194:2006 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 61190-1-3:2007+AMD1:2010 CSV | Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.