I.S. EN 61347-2-9:2013
Current
The latest, up-to-date edition.
LAMP CONTROLGEAR - PART 2-9: PARTICULAR REQUIREMENTS FOR ELECTROMAGNETIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) (IEC 61347-2-9:2012 (EQV))
Hardcopy , PDF
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Electromagnetic controlgear heating
15 High-voltage impulse testing
16 Fault conditions
17 Construction
18 Creepage distances and clearances
19 Screws, current-carrying parts and connections
20 Resistance to heat, fire and tracking
21 Resistance to corrosion
22 No-load output voltage
Annex A (normative) - Test to establish whether a conductive
part is a live part which may cause an electric shock
Annex B (normative) - Particular requirements for thermally
protected lamp electromagnetic controlgear
Annex C (normative) - Particular requirements for electronic
lamp controlgear with means of protection
against overheating
Annex D (normative) - Requirements for carrying out the
heating tests of thermally protected lamp
electromagnetic controlgear
Annex E (normative) - Use of constant S other than 4500
in tw tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of
the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Method for selection of varistors
Annex J (informative) - Explanation of electromagnetic
controlgear temperatures
Annex K (normative) - Additional requirements for built-in
electromagnetic controlgear with double or
reinforced insulation
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Describes particular safety requirements for electromagnetic controlgear for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps.
| DevelopmentNote |
Together with I.S. EN 61347-1 and parts 2-1, 2-2, 2-3, 2-4, 2-5, 2-6, 2-7 and 2-8 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| DIN EN 61347-2-9 : 2013 | Identical |
| EN 61347-2-9:2013 | Identical |
| UNE-EN 61347-2-9:2013 | Identical |
| NF EN 61347-2-9 : 2013 | Identical |
| SN EN 61347-2-9 : 2006 | Identical |
| BS EN 61347-2-9:2013 | Identical |
| EN 60188:2001 | High-pressure mercury vapour lamps - Performance specifications |
| EN 60192:2001 | Low pressure sodium vapour lamps - Performance specifications |
| IEC 60662:2011 | High-pressure sodium vapour lamps - Performance specifications |
| IEC 60192:2001 | Low-pressure sodium vapour lamps - Performance specifications |
| IEC 60188:2001 | High-pressure mercury vapour lamps - Performance specifications |
| IEC 61347-1:2015 RLV | Lamp controlgear - Part 1: General and safety requirements |
| EN 61347-2-1:2001/A2:2014 | LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) (IEC 61347-2-1:2000/A2:2013) |
| IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV | Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters) |
| IEC 61167:2015 | Metal halide lamps - Performance specification |
| IEC 62035:2014+AMD1:2016 CSV | Discharge lamps (excluding fluorescent lamps) - Safety specifications |
| EN 61347-1:2015 | Lamp controlgear - Part 1: General and safety requirements |
| EN 62035:2014 | Discharge lamps (excluding fluorescent lamps) - Safety specifications |
| IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
| EN 60662:2012 | High-pressure sodium vapour lamps - Performance specifications |
| IEC 60923:2005+AMD1:2006 CSV | Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements |
| IEC 61347-2-8:2000+AMD1:2006 CSV | Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.