I.S. EN 61290-10-1:2009
Current
The latest, up-to-date edition.
OPTICAL AMPLIFIERS - TEST METHODS - PART 10-1: MULTICHANNEL PARAMETERS - PULSE METHOD USING AN OPTICAL SWITCH AND OPTICAL SPECTRUM ANALYZER
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Abbreviated terms
4 Apparatus
5 Test sample
6 Procedure
6.1 Calibration
6.1.1 Calibration of OSA power measurement
6.1.2 Calibration of the pulse duty ratio
6.1.3 Calibration of the sampling module
6.1.4 Calibration of dynamic isolation
6.2 OA measurement
6.2.1 Timing adjustment for ASE and amplified signal
power measurement
6.2.2 ASE measurement
6.2.3 Amplified signal power measurement
7 Calculation
7.1 General
7.2 Noise factor calculation
7.3 ASE power
7.4 Gain calculation
7.5 Average output signal power
7.6 Noise figure calculation
8 Test results
Annex A (informative) - Output waveforms for various EDFAs
at 25 kHz and 500 kHz pulse rates
Annex B (informative) - Measurement accuracy versus pulse rate
Annex C (informative) - Pulse repetition frequency measurements
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Pertains to optical amplifiers (OAs) using active fibres and waveguides, containing rare-earth dopants, currently commercially available.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
60
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| SN EN 61290-10-1 : 2003 | Identical |
| IEC 61290-10-1:2009 | Identical |
| NF EN 61290-10-1 : 2009 | Identical |
| EN 61290-10-1:2009 | Identical |
| DIN EN 61290-10-1:2010-01 | Identical |
| BS EN 61290-10-1:2009 | Identical |
| EN 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61290-1-1:2015 | Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method |
| IEC 60874-1:2011 | Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification |
| IEC 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| IEC 61290-3:2008 | Optical amplifiers - Test methods - Part 3: Noise figure parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.