I.S. EN 60920:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BALLAST FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS
Hardcopy , PDF
06-04-2001
I.S. EN 61347-2-7:2012
I.S. EN 61347-2-8:2001
I.S. EN 61347-1:2015
I.S. EN 61347-2-5:2001
I.S. EN 61347-2-1:2004
I.S. EN 61347-2-9:2013
I.S. EN 61347-2-2:2012
I.S. EN 61347-2-6:2001
I.S. EN 61347-2-4:2001
I.S. EN 61347-2-3:2011
English
01-01-1992
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Cooperating organizations
National foreword
Foreword
Introduction
Section One - General requirements
1. Scope
2. Definitions
3. General requirements
4. General notes on tests
5. Classification
6. Marking
Section Two - Safety requirements
7. Protection against accidental contact with live
parts
8. Terminals
9. Provision for earthing
10. Moisture resistance and insulation
11. High-voltage impulse testing
12. Thermal endurance of windings
13. Ballast heating
14. Screws, current-carrying parts and connections
15. Creepage distances and clearances
16. Resistance to heat and fire
17. Resistance to corrosion
Appendices
A. Tests: General requirements and tests referring to
Section Two
B. Particular requirements for thermally protected
ballasts
C. The use of constants S other than 4500 in tw tests
D. Information for carrying out the heating tests of
thermally protected ballasts
E. Explanation to ballast temperatures
F. Method for selection of varistors
Figures
Annex ZA (normative) Other international publications
quoted in this standard with the references of the
relevant European publications
Annex ZB (informative) National A-deviations
National annex NA (informative)
National annex NB (informative)
National annex NC (informative)
Applies to ballasts, excluding resistance types, for use on a.c. supplies up to 1000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with or without pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC Publication 81. Applies to complete ballasts and to their component parts e.g. reactors, transformers and capacitors. Particular requirements for thermally protected ballasts are included. Ballasts for conventional operation of lamps at mains frequency are covered.
| DocumentType |
Standard
|
| Pages |
166
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SN EN 60920 : 1991 AMD 11 2000 | Identical |
| BS EN 60920:1991 | Identical |
| EN 60920:1991/A11:2000 | Identical |
| UNE EN 60920 : 1994 A11 2000 | Identical |
| DIN EN 60920 : 1993 AMD 11 | Identical |
| NF EN 60920 : 92 AMD 11 2001 | Identical |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.