I.S. EN 60464-2:2002
Current
The latest, up-to-date edition.
VARNISHES USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST
Hardcopy , PDF
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General notes on methods of test
5 Methods of test for undreid and/or uncured varnishes
5.1 Flashpoint
5.2 Density
5.3 Viscosity
5.4 Content of non-volatile matter
5.5 Dilution ability
5.6 Stability of varnish in an open vessel
5.7 Drying and/or curing in thick layer
5.8 Effect of varnish on enamelled winding wires
6 Methods of test for dried and/or cured varnishes
6.1 Test specimen
6.2 Mechanical properties
6.3 Thermal properties
6.4 Chemical properties
6.5 Electrical properties
Annex ZA (normative) Normative references to
international publications with their
corresponding European publications
Defines methods of test to be used for testing varnishes used for electrical insulation. This includes methods of test to be applied before and others to be applied after drying and/or curing of the varnish.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
52
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| UNE-EN 60464-2:2003 | Identical |
| DIN EN 60464-2 : 2006 COR 1 2007 | Identical |
| NBN EN 60464-2 : 2002 AMD 1 2006 | Identical |
| SN EN 60464-2 : AMD 1 2006 | Identical |
| EN 60464-2:2001/A1:2006 | Identical |
| NF EN 60464-2 : 2002 AMD 1 2006 | Identical |
| BS EN 60464-2:2001 | Identical |
| IEC 60464-2:2001+AMD1:2006 CSV | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| ISO 1514:2016 | Paints and varnishes — Standard panels for testing |
| ISO 2578:1993 | Plastics Determination of time-temperature limits after prolonged exposure to heat |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| EN ISO 2431:2011 | Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011) |
| ISO 3219:1993 | Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| IEC 60050-212:2010 | International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases |
| EN ISO 15528:2013 | Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO 15528:2013) |
| ISO 1520:2006 | Paints and varnishes Cupping test |
| EN ISO 2578:1998 | Plastics - Determination of time-temperature limits after prolonged exposure to heat (ISO 2578:1993) |
| EN 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| IEC 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
| ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
| HD 429 : 200S1 | METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
| EN ISO 1514:2016 | Paints and varnishes - Standard panels for testing (ISO 1514:2016) |
| ISO 15528:2013 | Paints, varnishes and raw materials for paints and varnishes Sampling |
| ISO 1523:2002 | Determination of flash point — Closed cup equilibrium method |
| ISO 2555:1989 | Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN ISO 1513:2010 | Paints and varnishes - Examination and preparation of test samples (ISO 1513:2010) |
| ISO 2078:1993 | Textile glass Yarns Designation |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| EN 456 : 1991 | PAINTS, VARNISHES AND RELATED PRODUCTS - DETERMINATION OF FLASHPOINT - RAPID EQUILIBRIUM METHOD |
| EN 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
| IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
| EN ISO 3219:1994 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| ISO 2113:1996 | Reinforcement fibres — Woven fabrics — Basis for a specification |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN ISO 1520:2006 | Paints and varnishes - Cupping test (ISO 1520:2006) |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| HD 323.2.10 : 200S3 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST J AND GUIDANCE: MOULD GROWTH |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| IEC 60641-3-1:2008 | Pressboard and presspaper for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Requirements for pressboard, types B.0.1, B.0.3, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.5.3 and B.6.1 |
| ISO 1513:2010 | Paints and varnishes Examination and preparation of test samples |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| ISO 1519:2011 | Paints and varnishes Bend test (cylindrical mandrel) |
| EN ISO 1519:2011 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| ISO 1144:2016 | Textiles Universal system for designating linear density (Tex System) |
| IEC 61033:1991 | Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate |
| ISO 558:1980 | Conditioning and testing — Standard atmospheres — Definitions |
| EN ISO 2808:2007 | Paints and varnishes - Determination of film thickness (ISO 2808:2007) |
| IEC 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
| ISO 2431:2011 | Paints and varnishes Determination of flow time by use of flow cups |
| EN 60641-3-1:2008 | Pressboard and presspaper for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Requirements for pressboard, types B.0.1, B.0.3, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.5.3 and B.6.1 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.