I.S. EN 60455-3-8:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: RESINS FOR CABLE ACCESSORIES (IEC 60455-3-8:2013 (EQV))
Hardcopy , PDF
07-09-2021
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Type testing
6 Test methods
7 Information on supply, packaging, marking and labelling
Annex ZA (normative) - Normative references to international
Publications with their corresponding European
publications
Bibliography
Provides the requirements for resins for power cable accessories which conform to this specification and meet established levels of performance.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60455-3-8:2013 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| HD 629.2 S2:2006/A1:2008 | TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 2: CABLES WITH IMPREGNATED PAPER INSULATION |
| ISO 7056:1981 | Plastics laboratory ware — Beakers |
| ISO 3521:1997 | Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| IEC 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| IEC 60455-1:1998 | Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements |
| ISO 4895:2014 | Plastics — Liquid epoxy resins — Determination of tendency to crystallize |
| EN ISO 4895:2014 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:2014) |
| HD 429 : 200S1 | METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
| ISO 2555:1989 | Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 61234-2:1997 | Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN 60212:2011 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| EN 50393:2015 | Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| HD 629.1 S2:2006/A1:2008 | TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 1: CABLES WITH EXTRUDED INSULATION |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.