I.S. EN 60400:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LAMPHOLDERS FOR TUBULAR FLUORESCENT LAMPS AND STARTERHOLDERS
Hardcopy , PDF
14-06-2021
English
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 General requirement
5 General conditions for tests
6 Electrical rating
7 Classification
8 Marking
9 Protection against electric shock
10 Terminals
11 Construction
12 Resistance to dust and moisture
13 Insulation resistance and electric strength
14 Endurance
15 Mechanical strength
16 Screws, current-carrying parts and connections
17 Creepage distances and clearances
18 Resistance to heat, fire and tracking
19 Resistance to excessive residual stresses (season cracking)
and to rusting
Annex A (normative) - Examples of lampholders
covered by IEC 60400
Annex B (normative) - Season cracking/corrosion test
Annex C (informative) - Protection against electric
shock - Explanatory details for the installation of
lampholders according to 92
Annex D (informative) - Clauses containing new or more
stringent requirements with respect to the previous edition
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European publications
Annex ZZ (informative) - Relationship between this European
standard and the safety objectives of Directive 2014/35/EU
[2014 OJ L96] aimed to be covered
Describes the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders.
DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
DocumentType |
Standard
|
Pages |
108
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
BS EN 60400:2017 | Identical |
NF EN 60400 : 2008 AMD 2 2014 | Identical |
EN 60400:2017 | Identical |
NBN EN 60400 : 2009 AMD 2 2014 | Identical |
UNE-EN 60400:2011 | Identical |
DIN EN 60400 : 2018 | Identical |
SN EN 60400 : 2017 | Identical |
IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
IEC 60238:2016+AMD1:2017 CSV | Edison screw lampholders |
IEC 60061-3:2005 CSV | Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges |
IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
IEC 60838-1:2016+AMD1:2017 CSV | Miscellaneous lampholders - Part 1: General requirements and tests |
IEC 60061-2:2005 CSV | Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders |
IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
EN 60399:2004/A1:2008 | BARREL THREAD FOR LAMPHOLDERS WITH SHADE HOLDER RING |
EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
IEC 60399:2004+AMD1:2008 CSV | Barrel thread for lampholders with shade holder ring |
IEC 61199:2011+AMD1:2012+AMD2:2014 CSV | Single-capped fluorescent lamps - Safety specifications |
IEC 60352-1:1997 | Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
IEC 60061-4:2005 CSV | Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4: Guidelines and general information |
IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
IEC 60061-1:2005 CSV | Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps |
EN 60155:1995/A2:2007 | GLOW-STARTERS FOR FLUORESCENT LAMPS |
EN 60352-1:1997 | Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
ISO 4046-4:2002 | Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
IEC 60155:1993 | Glow-starters for fluorescent lamps |
EN 60695-11-5:2017 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.