I.S. EN 60216-6:2004
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 6: DETERMINATION OF THERMAL ENDURANCE INDICES (TI AND RTE) OF AN INSULATING MATERIAL USING THE FIXED TIME FRAME METHOD
Hardcopy , PDF
24-11-2006
English
29-03-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated terms
3.1 Terms, abbreviations and definitions
3.2 Symbols and abbreviated terms
4 FTFM protocol - Principles and objectives
4.1 Principles of FTFM protocol
4.2 Objectives of FTFM protocol
5 TI determination
5.1 Ageing procedures
5.2 Ageing times and temperatures
5.3 Test specimens
5.4 Diagnostic tests
5.5 Selection of end-points
5.6 Establishment of initial property value
5.7 Ageing conditions
5.8 Procedure for ageing
6 Calculation procedures
6.1 General principles
6.2 Precision of calculations
6.3 Derivation of temperatures equivalent to property
values
6.4 Regression analysis (temperature on time)
6.5 Statistical tests
6.6 Thermal endurance graph
7 Calculation and requirements for results
7.1 Calculation of thermal endurance characteristics
7.2 Reporting of results
8 Report
9 RTE Determination - Objectives
10 Additional symbols
11 Experimental procedures
12 Calculation procedures
12.1 General principles
12.2 Input data
12.3 RTE
12.4 Confidence limits
12.5 Extrapolation
13 Results and report
13.1 Results of statistical and numerical tests
13.2 Result
13.3 Report
Annex A (normative) Decision flow chart
Annex B (normative) Decision table
Annex C (informative) Statistical tables
Annex D (informative) Suggested ageing times and temperatures
Annex E (informative) Figures
Annex F (normative) Statistical significance of the difference
between two regression estimates
Figures
Tables
Describes the experimental and calculation procedures for deriving the thermal endurance characteristics, temperature index (TI) and relative thermal endurance index (RTE) of a material using the fixed time frame method (FTFM).
| DocumentType |
Standard
|
| Pages |
98
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| BS EN 60216-6:2006 | Identical |
| EN 60216-6:2006 | Identical |
| DIN EN 60216-6 : 2007 | Identical |
| NBN EN 60216-6 : 2007 | Identical |
| NF EN 60216-6 : 2006 | Identical |
| IEC 60216-6:2006 | Identical |
| EN 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| HD 437 : 200S1 | STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS |
| IEC 60216-4-2:2000 | Electrical insulating materials - Thermal endurance properties - Part 4-2: Ageing ovens - Precision ovens for use up to 300 °C |
| IEC 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
| IEC 60493-1:2011 | Guide for the statistical analysis of ageing test data - Part 1: Methods based on mean values of normally distributed test results |
| EN 60216-4-2:2000 | Electrical insulating materials - Thermal endurance properties - Part 4-2: Ageing ovens - Precision ovens for use up to 300 °C |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| EN 60216-3:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
| HD 611.4.1 : 200S1 | GUIDE FOR THE DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - AGEING OVENS - SECTION ONE - SINGLE-CHAMBER OVENS |
| EN 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
| EN 60216-4-3:2000 | Electrical insulating materials - Thermal endurance properties - Part 4-3: Ageing ovens - Multi-chamber ovens |
| IEC 60216-4-3:2000 | Electrical insulating materials - Thermal endurance properties - Part 4-3: Ageing ovens - Multi-chamber ovens |
| IEC 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
| HD 611.2 : 200S1 | GUIDE FOR THE DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| IEC 60216-3:2006 | Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.