I.S. EN 50174-3:2013
Current
The latest, up-to-date edition.
INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
Hardcopy , PDF
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
Foreword
Introduction
1 Scope and conformance
2 Normative references
3 Terms, definitions and abbreviations
4 Requirements for planning installations of
information technology cabling
5 Requirements for the installation of
information technology cabling
6 Segregation
7 Additional installation practices for
specific sites and services
Annex A (informative) - EMC and protection
Annex B (informative) - Earth potential rise (EPR)
Annex C (informative) - Application of responsibilities
Annex D (informative) - A-deviations
Bibliography
Describes requirements and gives recommendations for the following aspects of information technology cabling: a) planning; b) installation practice.
DocumentType |
Standard
|
Pages |
120
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Current
|
Standards | Relationship |
BS EN 50174-3 : 2013 | Identical |
UNE-EN 50174-3:2005 | Identical |
EN 50174-3:2013/A1:2017 | Identical |
NBN EN 50174-3 : 2013 | Identical |
NEN EN 50174-3 : 2013 AMD 1 2017 | Identical |
DIN EN 50174-3 : 2017 | Identical |
SN EN 50174-3 : 2013 AMD 1 2017 | Identical |
NF EN 50174-3 : 2014 AMD 1 2017 | Identical |
IEC 61537:2006 | Cable management - Cable tray systems and cable ladder systems |
IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
EN 60794-3-10:2015 | Optical fibre cables - Part 3-10: Outdoor cables - Family specification for duct, directly buried or lashed aerial optical telecommunication cables |
IEC TR 61000-5-3:1999 | Electromagnetic compatibility (EMC) - Part 5-3: Installation and mitigation guidelines - HEMP protection concepts |
IEC 60364-5-534:1997 | Electrical installations of buildings - Part 5: Selection and erection of electrical equipment - Section 534: Devices for protection against overvoltages |
IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
IEC 60794-3:2014 | Optical fibre cables - Part 3: Outdoor cables - Sectional specification |
IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
EN 50411-2-9:2010 | Fibre organisers and closures to be used in optical fibre communications systems - Product specifications - Part 2-9: Non-sealed closures for air blown fibre microduct cable, for category S & A |
PREN 50700 : DRAFT 2012 | INFORMATION TECHNOLOGY - PREMISES DISTRIBUTION ACCESS NETWORK (PDAN) CABLING TO SUPPORT DEPLOYMENT OF OPTICAL BROADBAND NETWORKS |
IEC 61663-1:1999 | Lightning protection - Telecommunication lines - Part 1: Fibre optic installations |
EN 60794-3-20:2016 | Optical fibre cables - Part 3-20: Outdoor cables - Family specification for self-supporting aerial telecommunication cables |
EN 62368-1:2014/AC:2017-03 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED) |
EN 60794-3-40:2008 | Optical fibre cables - Part 3-40: Outdoor cables - Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers |
IEC 60794-3-40:2008 | Optical fibre cables - Part 3-40: Outdoor cables - Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers |
EN 50174-1:2009/A2:2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 1: INSTALLATION SPECIFICATION AND QUALITY ASSURANCE |
EN 61969-1:2012 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines |
IEC 61969-1:2011 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines |
EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
IEC 60794-3-12:2012 | Optical fibre cables - Part 3-12: Outdoor cables - Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling |
IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
EN 50411-2-5:2009 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 2-5: Sealed closures for air blown fibre microduct, type 1, for category S & A |
EN 60794-3:2015 | Optical fibre cables - Part 3: Sectional specification - Outdoor cables |
IEC 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
HD 60364-5-54:2011/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
EN 13501-6:2014 | Fire classification of construction products and building elements - Part 6: Classification using data from reaction to fire tests on electric cables |
EN 12613:2009 | Plastics warning devices for underground cables and pipelines with visual characteristics |
IEC 61663-2:2001 | Lightning protection - Telecommunication lines - Part 2: Lines using metallic conductors |
IEC 60794-3-10:2015 | Optical fibre cables - Part 3-10: Outdoor cables - Family specification for duct, directly buried and lashed aerial optical telecommunication cables |
EN 60794-3-50 : 2008 | OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN GAS PIPES |
IEC 60794-3-11:2010 | Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried, and lashed aerial single-mode optical fibre telecommunication cables |
HD 637 S1:1999/corrigendum:2005 | POWER INSTALLATIONS EXCEEDING 1 KV A.C. |
EN 60794-3-12:2013 | Optical fibre cables - Part 3-12: Outdoor cables - Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling |
EN 60794-5-10:2014 | Optical fibre cables - Part 5–10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
EN 61663-2 : 2001 | LIGHTNING PROTECTION - TELECOMMUNICATION LINES - PART 2: LINES USING METALLIC CONDUCTORS |
EN 60332-1-2:2004/A11:2016 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015) |
IEC 61969-2:2011 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 2: Coordination dimensions |
EN 50700:2014 | Information technology - Premises distribution access network (PDAN) cabling to support deployment of optical broadband networks |
EN 50173-3 : 2007 COR 2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 3: INDUSTRIAL PREMISES |
IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
EN 61663-1 : 1999 | LIGHTNING PROTECTION - TELECOMMUNICATION LINES - PART 1 - FIBRE OPTIC INSTALLATIONS |
EN 61386-1:2008 | Conduit systems for cable management - Part 1: General requirements |
IEC 60601-1-2:2014 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
HD 60364-4-444:2010/AC:2012 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-444: PROTECTION FOR SAFETY - PROTECTION AGAINST VOLTAGE DISTURBANCES AND ELECTROMAGNETIC DISTURBANCES |
EN 50173-1:2011 | Information technology - Generic cabling systems - Part 1: General requirements |
EN 60601-1-2:2015 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
EN 50085-1 : 2005 AMD 1 2013 | CABLE TRUNKING SYSTEMS AND CABLE DUCTING SYSTEMS FOR ELECTRICAL INSTALLATIONS - PART 1: GENERAL REQUIREMENTS |
HD 60364-5-534:2016 | Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control - Clause 534: Devices for protection against transient overvoltages |
IEC 60364-4-444:1996 | Electrical installations of buildings - Part 4: Protection for safety - Section 444: Protection against electromagnetic interferences (EMI) in installations of buildings |
EN 50174-2 : 2009 AMD 2 2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
IEC 60794-3-30:2008 | Optical fibre cables - Part 3-30: Outdoor cables - Family specification for optical telecommunication cables for lakes, river crossings and coastal application |
EN 60794-3-11:2010 | Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables |
EN 60794-4-20:2012 | OPTICAL FIBRE CABLES - PART 4-20: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR ADSS (ALL DIELECTRIC SELF SUPPORTED) OPTICAL CABLES (IEC 60794-4-20:2012) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN 60794-3-60:2008 | Optical fibre cables - Part 3-60: Outdoor cables - Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes |
EN 50341-1:2012 | Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications |
IEC 60794-3-21:2015 | Optical fibre cables - Part 3-21: Outdoor cables - Product specification for optical self-supporting aerial telecommunication cables for use in premises cabling |
IEC 60794-3-60:2008 | Optical fibre cables - Part 3-60: Outdoor cables - Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes |
IEC 60794-5-10:2014 | Optical fibre cables - Part 5-10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
EN 61969-2:2012 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 2: Coordination dimensions |
EN 50411-2-4:2012 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 2-4: Sealed dome fibre splice closures Type 1, for category S & A |
IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
EN 61300-3-35:2015 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers |
EN 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
IEC 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
EN 60794-1-2:2017/AC:2017-07 | OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL GUIDANCE (IEC 60794-1-2:2017) |
EN 60794-3-21:2016 | Optical fibre cables - Part 3-21: Outdoor cables - Product specification for optical self-supporting aerial telecommunication cables for use in premises cabling |
IEC 60794-3-50:2008 | Optical fibre cables - Part 3-50: Outdoor cables - Family specification for gas pipe cables and subducts for installation by blowing and/or pulling/dragging in gas pipes |
EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
IEC 60050-826:2004 | International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations |
EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
IEC 61386-1:2008+AMD1:2017 CSV | Conduit systems for cable management - Part 1: General requirements |
EN 60794-3-30:2008 | OPTICAL FIBRE CABLES - PART 3-30: OUTDOOR CABLES - FAMILY SPECIFICATION FOR OPTICAL TELECOMMUNICATION CABLES FOR LAKES, RIVER CROSSINGS AND COASTAL APPLICATION |
EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
IEC 60794-3-20:2016 | Optical fibre cables - Part 3-20: Outdoor cables - Family specification for self-supporting aerial telecommunication cables |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
EN 60825-2:2004/A2:2010 | SAFETY OF LASER PRODUCTS - PART 2: SAFETY OF OPTICAL FIBRE COMMUNICATION SYSTEMS (OFCS) |
EN 61537:2007 | Cable management - Cable tray systems and cable ladder systems |
CLC/TR 50173-99-2:2010 | Information technology - Implementation of BCT applications using cabling in accordance with EN 50173-4 |
EN 50173-5 : 2007 AMD 2 2012 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 5: DATA CENTRES |
EN 50173-4 : 2007 AMD 2 2012 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 4: HOMES |
EN 50310:2016 | Telecommunications bonding networks for buildings and other structures |
EN 50411-2-2:2012 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 2-2: Sealed pan fibre splice closures Type 1, for category S & A |
EN 50173-6:2013 | Information technology - Generic cabling systems - Part 6: Distributed building services |
IEC 62368-1:2014 | Audio/video, information and communication technology equipment - Part 1: Safety requirements |
EN 50411-2-3:2012 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 2-3: Sealed inline fibre splice closures Type 1, for category S & A |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.