I.S. EN 15011:2011
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
CRANES - BRIDGE AND GANTRY CRANES
Available format(s)
Hardcopy , PDF
Withdrawn date
30-06-2021
Superseded by
Language(s)
English
Published date
01-01-2011
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of safety requirements and/or protective
measures
7 Information for use
Annex A (informative) - Guidance for specifying the
operating duty according to EN 13001-1
Annex B (informative) - Guidance for specifying the
classes P of average number of accelerations
according to EN 13001-1
Annex C (informative) - Calculation of dynamic coefficient
h(t)
Annex D (normative) - Loads caused by skewing
Annex E (informative) - Local stresses in wheel supporting
flanges
Annex F (normative) - Noise test code
Annex G (informative) - Actions on crane supporting structures
induced by cranes
Annex H (informative) - Selection of a suitable set of crane
standards for a given application
Annex ZA (informative) - Relationship between this European
standard and the Essential Requirements of
EU Directive 2006/42/EC
Bibliography
Pertains to bridge and gantry cranes able to travel by wheels on rails, runways or roadway surfaces, and to gantry cranes without wheels mounted in a stationary position.
| DevelopmentNote |
2011 Edition Re-Issued in March 2014 & incorporates AMD 1 2014. (03/2014)
|
| DocumentType |
Standard
|
| Pages |
92
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| EN 15011:2011+A1:2014 | Identical |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 81-43:2009 | Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 12385-4:2002+A1:2008 | Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications |
| EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 11660-5:2001 | Cranes — Access, guards and restraints — Part 5: Bridge and gantry cranes |
| EN 60947-5-5 : 1997 AMD 2 2016 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-5: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTRICAL EMERGENCY STOP DEVICE WITH MECHANICAL LATCHING FUNCTION (IEC 60947-5-5:1997/A2:2016) |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 15513:2000 | Cranes — Competency requirements for crane drivers (operators), slingers, signallers and assessors |
| EN 13155:2003+A2:2009 | Cranes - Safety - Non-fixed load lifting attachments |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| ISO 12480-1:1997 | Cranes — Safe use — Part 1: General |
| ISO 9926-1:1990 | Cranes — Training of drivers — Part 1: General |
| EN 12644-2:2000+A1:2008 | Cranes - Information for use and testing - Part 2: Marking |
| ISO 9374-5:1991 | Cranes Information to be provided Part 5: Overhead travelling cranes and portal bridge cranes |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 12488-1:2012 | Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General |
| HD 60364-4-41:2017/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| ISO 16881-1:2005 | Cranes — Design calculation for rail wheels and associated trolley track supporting structure — Part 1: General |
| EN 13586:2004+A1:2008 | Cranes - Access |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 12644-1:2001+A1:2008 | Cranes - Information for use and testing - Part 1: Instructions |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 9374-1:1989 | Cranes — Information to be provided — Part 1: General |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors |
| ISO 11203:1995 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level |
| EN 13157:2004+A1:2009 | Cranes - Safety - Hand powered cranes |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 2631-1:1997 | Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements |
| EN 60204-11:2000/corrigendum:2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 4301-1:2016 | Cranes — Classification — Part 1: General |
| ISO 22986:2007 | Cranes — Stiffness — Bridge and gantry cranes |
| EN 795:2012 | Personal fall protection equipment - Anchor devices |
| ISO 8566-5:2017 | Cranes — Cabins and control stations — Part 5: Overhead travelling and portal bridge cranes |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 12482-1:1995 | Cranes Condition monitoring Part 1: General |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN ISO 11203:2009 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) |
| ISO 7752-5:1985 | Lifting appliances Controls Layout and characteristics Part 5: Overhead travelling cranes and portal bridge cranes |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| PREN 13001-3-3 : DRAFT 2012 | CRANES - GENERAL DESIGN - PART 3-3: LIMIT STATES AND PROOF OF COMPETENCE OF WHEEL/RAIL CONTACTS |
| ISO 10245-5:1995 | Cranes — Limiting and indicating devices — Part 5: Overhead travelling and portal bridge cranes |
| CEN/TS 13001-3-2:2008 | Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems |
| IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV | Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.